Manual Makita DCS550 (page 5 of 56) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

600551

Zoom out

Zoom in

1/56

not in line with the blade. Kickback could cause the

tool to jump backwards, but kickback forces can be

controlled by the operator, if proper precautions are

taken.

10. When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the

tool motionless in the material until the blade

comes to a complete stop. Never attempt to

remove the tool from the work or pull the tool

backward while the blade is in motion or kickback

may occur. Investigate and take corrective actions to

eliminate the cause of blade binding.

11. When restarting a tool in the workpiece, center the

blade in the kerf and check that blade teeth are not

engaged into the material. If blade is binding, it may

walk up or kickback from the workpiece as the tool is

restarted.

12. Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag

under their own weight. Supports must be placed

under the panel on both sides, near the line of cut and

near the edge of the panel.

13. Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

14. Blade depth and bevel adjusting locking levers

must be tight and secure before making cut. If

blade adjustment shifts while cutting, it may cause

binding and kickback.

15. Use extra caution when making a “plunge cut”

into existing walls or other blind areas. The

protruding blade may cut objects that can cause

kickback. For plunge cuts, retract lower guard using

retracting handle.

Lower guard function

16. Check lower guard for proper closing before each

use. Do not operate the tool if lower guard does

not move freely and close instantly. Never clamp

or tie the lower guard into the open position. If tool

is accidentally dropped, lower guard may be bent.

Raise the lower guard with the retracting lever and

make sure it moves freely and does not touch the

blade or any other part, in all angles and depths of cut.

17. Check the operation and condition of the lower

guard spring. If the guard and the spring are not

operating properly, they must be serviced before

use. Lower guard may operate sluggishly due to

damaged parts, gummy deposits, or a buildup of

debris.

18. Lower guard may be retracted manually only for

special cuts such as “plunge cuts” and

“compound cuts”. Raise lower guard by retracting

handle and as soon as blade enters the material,

the lower guard must be released. For all other

sawing, the lower guard should operate automatically.

19. Always observe that the lower guard is covering

the blade before placing tool down on bench or

floor. An unprotected, coasting blade will cause the

tool to walk backwards, cutting whatever is in its path.

Be aware of the time it takes for the blade to stop after

switch is released.

20. To check lower guard, open lower guard by hand,

then release and watch guard closure. Also check

to see that retracting handle does not touch tool

housing. Leaving blade exposed is VERY

DANGEROUS and can lead to serious personal injury.

Additional safety warnings

21. Do not stop the blades by lateral pressure on the

blade.

22. DANGER:

Do not attempt to remove cut material when blade

is moving.

CAUTION: Blades coast after turn off.

23. Place the wider portion of the tool base on that

part of the workpiece which is solidly supported,

not on the section that will fall off when the cut is

made.

24. Never attempt to make a cut with the tool held

upside down in a vise. This is extremely

dangerous and can lead to serious accidents.

25. Wear safety goggles and hearing protection

during operation.

26. Always use blades recommended in this manual.

Do not use any abrasive wheels.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product (gained

from repeated use) replace strict adherence to safety

rules for the subject product. MISUSE or failure to

follow the safety rules stated in this instruction

manual may cause serious personal injury.

IMPORTANT SAFETY

INSTRUCTIONS

ENC007-8

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all

instructions and cautionary markings on (1)

battery charger, (2) battery, and (3) product using

battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively shorter,

stop operating immediately. It may result in a risk

of overheating, possible burns and even an

explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a

breakdown.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DCS550 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DCS550 Manual

Product: