If the saw is used intensively it will be necessary to lubricate the return sprocket bear-
ings regularly (once a week). To do this, first thoroughly clean the 2 mm hole at the tip
of the guide bar, and then press in a small amount of multi-purpose grease.
Multi-purpose grease and grease guns are available as accessories.
Multi-purpose grease 944 360 000
Grease guns 944 350 000
Replacing the saw chain (Fig. 55)
CAUTION: Use only chains and guide bars designed for this saw.
Check the sprocket (10) before mounting a new chain.
CAUTION: Worn out sprockets may damage the new chain and must therefore be
replaced.
Replacing the suction head (Fig. 56)
The felt filter (12) of the suction head can become clogged. It is recommended to
replace the suction head once every three months in order to ensure unimpeded fuel
flow to the carburetor.
To remove the suction head for replacement, pull it out through the tank filler neck
using a piece of wire bent at one end to form a hook.
Cleaning the air filter (Fig. 57)
Unscrew screw (14) and remove the cleaner case cover (13).
IMPORTANT: Cover the intake opening with a clean cloth in order to prevent dirt par-
ticles from falling into the carburetor. Remove the air filter (15).
CAUTION: To prevent injury to the eyes, do NOT blow out dirt particles! Do not
use fuel to clean the air filter.
Clean the air filter with a soft brush.
If the filter is very dirty, clean it in lukewarm water with dishwashing detergent.
Let the air filter dry completely.
If the filter is very dirty, clean it frequently (several times a day), because only a clean
air filter provides full engine power.
CAUTION:
Replace damaged air filters immediately.
Pieces of cloth or large dirt particles can destroy the engine!
Replacing the spark plug (Fig. 58)
CAUTION:
Do not touch the spark plug or plug cap if the engine is running (high voltage).
Switch off the engine before starting any maintenance work. A hot engine can
cause burns. Wear protective gloves!
The spark plug must be replaced in case of damage to the insulator, electrode ero-
sion (burn) or if the electrodes are very dirty or oily.
Remove the cleaner case cover (see “Cleaning the air filter”).
Pull the plug cap (1) off the spark plug. Use only the combination wrench supplied
with the saw to remove the spark plug.
CAUTION: Use only the following spark plugs: NGK CMR6A.
Electrode gap (Fig. 59)
The electrode gap must be 0.6 – 0.7 mm.
Cleaning the inlet port of the cooling air (Fig. 60)
Unscrew four screws (2). Remove recoil starter (3).
Clean the inlet port (4) and the cylinder fins.
Cleaning the muffler (Fig. 61)
CAUTION: If the engine is hot there is a risk of burning. Wear protective gloves.
Remove the sprocket cover (see “PUTTING INTO OPERATION”).
Remove deposits of carbon from the exhaust outlets (11) of the muffler.
Cleaning the cylinder space (Fig. 62)
Remove the sprocket cover (see “PUTTING INTO OPERATION”).
If necessary remove muffler by loosening and removing the two screws (14).
Stuff a rag into the cylinder port (15).
Use a suitable tool (wooden scraper) to clean out the cylinder space (16), especially
the cooling fins.
Remove the rag from the cylinder port and refit the muffler according to the diagram.
Replace the gasket (13) if necessary. Carefully remove any pieces of the old gasket
from the muffler.
Ensure correct mounting position.
The cowling should follow the contour of the cylinder to ensure correct heat transfer.
Tighten screws (14) to 10 Nm while the engine is cold.
Instructions for periodic maintenance
To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed regularly. Guarantee claims can be rec-
ognized only if this work is performed regularly and properly. Failure to perform the prescribed maintenance work can lead to accidents!
The user of the chain saw must not perform maintenance work which is not described in the instruction manual. All such work must be carried out by a MAKITA service centre.
STOP
STOP
STOP
GeneralChain sawClean exterior, check for damage. In case of damage, have repaired by a qualified service centre
immediately.
Saw chainSharpen regularly, replace in good time.
Chain brakeHave inspected regularly at an authorized service centre.
Guide barTurn over to ensure even wear of bearing surfaces.
Replace in good time.
Before each startSaw chainInspect for damage and sharpness.
Check chain tension.
Guide barCheck for damage.
Chain lubricationFunctional check.
Chain brakeFunctional check.
OFF switch, Safety locking button,
Throttle lever
Functional check.
Fuel/oil tank plugCheck for tightness.
Every dayAir filterClean.
Guide barCheck for damage, clean oil intake bore.
Guide bar supportClean, in particular the oil guide groove.
Idle speedCheck (chain must not run).
Every weekFan housingClean to ensure proper air cooling.
Cylinder spaceClean.
Spark plugCheck and replace if necessary.
MufflerCheck tightness of mounting.
Chain catch sleeveCheck for damage, replace if necessary.
Every 3 monthsSuction headReplace.
Fuel, oil tanksClean.
StorageChain sawClean exterior, check for damage. In case of damage, have repaired by a qualified service centre
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Makita DCS232T at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Makita DCS232T in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.
The manual is 3,56 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
