Manual Makita DCS 3410 (page 16 of 28) (English)

79160

Zoom out

Zoom in

1/28

Cold start:

Prime the fuel pump (6) by pressing it several times until you

can see fuel in the pump.

Move the short-circuit switch (3) forward in the direction of the

arrow.

Turn the choke lever (5) up (see “Cold start” illustration).

This

simultaneously actuates the half-throttle lock.

Slowly pull out the starter cable (4) until you notice resistance

(the piston is positioned before the top dead centre).

Now pull the starter cable with a fast and forceful movement

until you hear the ﬁ rst ignition.

CAUTION: Do not pull out the starter cable more than approx. 50

cm, and lead it back by hand. For efﬁ cient starting, it is important

to pull the starter cable quickly and powerfully.

Turn the choke lever (5) down (see “Warm start” illustration)

and pull the starter cable again.

As soon as the engine is

running, grasp the rear handle (this actuates the grip safety (2))

and tap the throttle (1). This will release the half-throttle lock

and the engine will run in idle.

Caution: The engine is to be run at idling speed immediately

after starting or damage may occur to the chain brake.

Now release the chain brake.

Warm start:

As for cold start, except before pulling the starter cable, turn

the choke lever (5) brieﬂ y to the “Cold start” position and

then immediately back to “Warm start” (this activates the

half-throttle lock).

Important: If the fuel tank has been completely emptied and the

engine has stopped due to lack of fuel

prime the fuel pump (6) by

pressing it several times until you can see fuel in the pump.

Stopping the engine

Put the short-circuiting switch (3) in position „STOP“.

Starting the engine

Do not start the saw until it has been completely assembled

and inspected!

Move at least 3m away from the place where you fuelled the

saw.

Make sure you have a good footing, and place the saw on the

ground in such a way that the chain is not touching anything.

Engage the chain brake (lock).

Grasp the rear handle ﬁ rmly in one hand and hold the saw

ﬁ rmly against the ground. Press with one knee on the rear

handle.

IMPORTANT: The choke switch (5) is coupled to the throttle lever (1). It will revert to its original position automatically once

the throttle lever has been pressed.

If the throttle lever is pressed before the engine starts, then the choke switch (5) will have to be reset to the appropriate

position.

Cold start Warm starting

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DCS 3410 in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita DCS 3410

Makita DCS 3410 User Manual - German, Italian - 80 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DCS 3410 Manual

Product: