793611
11
Zoom out
Zoom in
Previous page
1/84
Next page
11 ENGLISH
NOTE:-
ment easier.

suction hole
1. -
priate size.
Fig.5: 1. Abrasive paper 2. Pad
2.



3.
-


4. 
between the clamp and sanding base.
5. -

6. Set the clamp lever back in a locked position to

7. Release the clamp on the other end, and have the

8. 
then set the clamp lever on the other end in a locked
position.
Fig.6: 1. Abrasive paper 2. Clamp 3. Sanding base
4. Clamp lever 5. Stopper
9.
Cover the abrasive paper with the punch plate with


Fig.7: 1. Abrasive paper 2. Punch plate
3. Positioning stoppers 4. Pad 5. Sanding
base
10. Push the punch plate over the abrasive paper to
make dust-suction holes.
11. To remove the abrasive paper, release the clamps
󰀨

suction hole
Optional accessory
1.



2.
-


3. 
aligning the dust-suction holes in the paper with those
in the pad.
Fig.8: 1. Abrasive paper 2. Pad 3. Dust-suction hole
4. 
between the clamp and sanding base.
5. Set the clamp lever back in a locked position so

6. Release the clamp on the other end, and have the

7. 
then set the clamp lever on the other end in a locked
position.
Fig.9: 1. Abrasive paper 2. Clamp 3. Sanding base
4. Clamp lever 5. Stopper
8. To remove the abrasive paper, release the clamps
󰀨

CAUTION: Make sure to install a hook-and-
 A loose attach-


CAUTION: 

attached.
CAUTION: 


For DBO480
1. 
and-loop pad.
2. 
paper to the pad, aligning the dust-suction holes in the
paper with those in the pad.
Fig.10: 1. Abrasive paper 2. Pad 3. Dust-suction
holes
3.
󰀨
For DBO481 and DBO482
NOTICE: 


hole or the circular groove around the center of

DBO481
Fig.11: 1. Cap 2. Sanding base 3. Circular hole
DBO482
Fig.12: 1. O-ring 2. Sanding base 3. Circular groove
1. 
pad to the sanding base.
Fig.13: 1. Screws 2. Pad 3. Sanding base
2. Replace the standard-equipped pad with an
optional hook-and-loop pad.
3. 
and-loop pad.
Fig.14: 1. Abrasive paper 2. Pad 3. Dust-suction
holes
4. 
and-loop pad.
5. 
paper to the pad, aligning the dust-suction holes in the
paper with those in the pad.
Fig.15: 1. Abrasive paper 2. Pad 3. Dust-suction
holes
6. 󰀨
edge.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DBO482 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DBO482 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 13.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info