Manual Makita DBO180ZJ (page 7 of 12) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

711196

Zoom out

Zoom in

1/12

Installing paper filter bag (optional accessory)

(Fig. 8 & 9)

Make sure that the logo on the cardboard lip and the logo

on the dust box are on the same side, then install the

paper filter bag by fitting the cardboard lip in the groove

of each holding tab.

Make sure that the logo on the cardboard lip and the logo

on the dust nozzle are on the same side, then install the

dust nozzle on the dust box.

Removing dust box and paper filter bag

(Fig. 10 & 11)

Remove the dust nozzle by pushing the two latches.

Remove the paper filter bag first by pinching the logo

side of its cardboard lip, then by pulling the cardboard lip

downwards to move it out of the holding tab of the dust

box.

Removing and reinstalling the skirt

(Fig. 12, 13 & 14)

CAUTION:

• Do not use the tool without the skirt. Otherwise dust is

scattered all over.

You can choose one of 12 directions of the skirt in accor-

dance with your purpose.

To remove the skirt, remove the screw and remove the

skirt with slightly opening it for both sides.

To reinstall the skirt, install it with slightly opening it for

both sides. And fasten the screw.

CAUTION:

• Do not set the skirt other than the designated angle.

Otherwise the tool may be damaged.

OPERATION

WARNING:

• Never switch on the tool when it is in contact with the

workpiece, it may cause an injury to operator.

Sanding operation (Fig. 15)

CAUTION:

• Never run the tool without the abrasive disc. You may

seriously damage the pad.

• Never force the tool. Excessive pressure may decrease

the sanding efficiency, damage the abrasive disc or

shorten tool life.

• Using the tool with the pad edge contacting the work-

piece may damage the pad.

Hold the tool firmly. Turn the tool on and wait until it

attains full speed. Then gently place the tool on the work-

piece surface. Keep the pad flush with the workpiece and

apply slight pressure on the tool.

CAUTION:

• The sanding pad rotates clockwise during the loaded

operation, but it may rotate counterclockwise during the

no-load operation.

Polishing operation (optional)

CAUTION:

• Use only a Makita genuine sponge pad, felt pad or wool

pad (optional accessories).

• Always operate the tool at low speed to prevent work

surfaces from heating abnormally.

• Never force the tool. Excessive pressure may decrease

the polishing efficiency and cause motor overload,

resulting in tool malfunction.

1. Applying wax (Fig. 16)

Use an optional sponge pad. Apply wax to the

sponge pad or work surface. Run the tool at low

speed to smooth out wax.

NOTE:

• First, wax a not conspicuous portion of the work sur-

face to make sure that the tool will not scratch the sur-

face or result in uneven waxing.

• The tool starts with high speed mode. Be careful when

you start the tool. The wax may be spattered. It is rec-

ommended that you spread wax with the tool stopped

before starting up the tool. Change the speed mode to

low immediately after you start the tool.

• Always run the tool at low speed. Running it at high

speed may cause the wax to spatter.

2. Removing wax (Fig. 17)

Use an optional felt pad. Run the tool at low speed

to remove wax.

3. Polishing (Fig. 18)

Use an optional wool pad. Run the tool at low speed

and apply the wool pad gently to the work surface.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Hook-and-loop type abrasive discs (with pre-punched

holes)

• Hook-and-loop type sponge pad

• Hook-and-loop type felt pad

• Hook-and-loop type wool pad

• Makita genuine battery and charger

•Dust box

• Paper filter bag

•Dust bag

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DBO180ZJ in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 0,77 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DBO180ZJ Manual

Product: