Manual Makita DBN600 (page 8 of 76) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

691775

Zoom out

Zoom in

1/76

8 ENGLISH

Overload protection

When the tool/battery is operated in a manner that

causesittodrawanabnormallyhighcurrent,thetool

automatically stops without any indication. In this sit-

uation,turnthetooloffandstoptheapplicationthat

causedthetooltobecomeoverloaded.Thenturnthe

tool on to restart.

Overheat protection

Whenthetool/batteryisoverheated,thetoolstops

automatically.Inthissituation,letthetool/batterycool

beforeturningthetoolonagain.

Overdischarge protection

Whenthebatterycapacityisnotenough,thetoolstops

automaticallyandthebatteryindicatorshowsfollowing

state.Inthiscase,removethebatteryfromthetooland

charge the battery.

Off

Blinking

Indicating the remaining battery

capacity

Only for battery cartridges with the indicator

►Fig.2: 1. Indicator lamps 2. Check button

Pressthecheckbuttononthebatterycartridgetoindi-

catetheremainingbatterycapacity.Theindicatorlamps

lightupforafewseconds.

Indicator lamps Remaining

capacity

Lighted Off Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

Thebattery

may have

malfunctioned.

NOTE:Dependingontheconditionsofuseandthe

ambienttemperature,theindicationmaydifferslightly

fromtheactualcapacity.

Trigger-lock button

CAUTION: When not operating the tool,

depress the trigger-lock button from B side to

lock the switch trigger in the OFF position.

Topreventtheswitchtriggerfromaccidentallypulled,

the trigger-lock button is provided.

Topulltheswitchtrigger,depressthetrigger-lockbutton

fromAside.

Afteruse,alwayspressinthetrigger-lockbuttonfrom

B side.

►Fig.3: 1.Trigger-lockbutton2.Switchtrigger

Nailing mode selection

Thetoolemploystwonailingactions.Selectthedesired

nailing by the mode selecting switch.

►Fig.4: 1. Mode selecting switch 2.Sequentialmode

3. Continuous mode

Intermittent nailing (sequential mode)

Thismodesuitsfordrivinganailcarefullyand

accurately.

Continuous/ intermittent nailing (continuous mode)

Whenthetoolissettothismode,youcanchooseeither

continuousorintermittentnailingbysequencesofthe

trigger operation.

Adjusting the nailing depth

WARNING: Always make sure that your

ngers are not placed on the switch trigger or

the contact element and the battery cartridge is

removed before adjusting the depth of nailing.

Turntheadjustertoadjustthenailingdepth.Thenailing

depthgetsdeeperasyouturntheadjustertoAdirec-

tion,shallowertoBdirectioninthegure.Therangeof

thenailingdepthadjustmentis3mm.

►Fig.5: 1.Adjuster

NOTICE: Do not turn the adjuster too much, or

the adjuster may get stuck.

Adjustthenailingdepthasnecessary.

►Fig.6: 1.Toodeep2. Flush 3.Tooshallow

Lighting up the lamp

CAUTION: Do not look in the light or see the

source of light directly.

Pulltheswitchtriggeroractuatethecontactelementto

lightupthelamp.Thelampkeepsonlightingwhilepull-

ing the switch trigger or actuating the contact element.

Thelampgoesoutapproximately10secondsafter

releasing the switch trigger and the contact element.

►Fig.7: 1. Lamp

Ddhdhbhdhdhdnndhdhddbdnndnndnndndndndndndnxjdndjdnndndndhdndndn ddidnenjjd(dndnd HD dndnd. Dan hehrhrhrrhhejejrjehrjdjrjejej Submitted on 10-12-2020 at 11:05
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita DBN600 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 16,65 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita DBN600 Manual

Product: