78789

Makita DBM 131 Manual

7
Zoom out
Zoom in
Previous page
1/61
Next page
df
Technical Characteristics
Rated voltage: 110 V
Rated power input: 1500 W
Load speed: 1
st
speed 0 - 800 min
-1
2
nd
speed 0 - 1570 min
-1
maximum drilling capacity:
1
st
speed 132 mm
2
nd
speed 70 mm
Protection class: II
Collet: M 18
Weight(net): 6.8 kg
Collar clamping diameter: 53 mm
This machine is meant for professional use only!
All rights of changes due to technical development reserved.
Safety Instructions
Read and obey these instructions before using this machine.
ADDITIONAL SAFETY RULES FOR THIS MACHINE
1. This core-drill must only be used under constant supervision. Unplug and make sure the mains
switch is OFF whenever core-drill is not in use or left unattended, before servicing, adjustments,
change of cutter or other accessories and when there is a voltage drop (below 200V)
2. Only grip by insulated part of auxiliary handle and other plastic surfaces when performing drilling
where cutter is likely to contact hidden electrical wiring or its own cable. Contact with a “Live”
wiring will make all exposed metal surfaces of the machine “Live” and danger for an electric
shock.
3. Do not use the machine if a defect is found on the plug, mains lead, trigger switch or any part of
housings (daily inspection). Have them repaired by a qualified person.
4. For longer machine use, wear hearing protectors.
5. Machine should never be damp or wet. Do not use the machine in damp or wet locations.
6. Likewise it is recommended to wear safety helmet, safety glasses and/or face shield. Also wear
a dust mask and thickly padded gloves.
7. Prior to work starting, make sure that cutting accessory is fitted properly.
8. Before starting work carefully check all screws for tightness. Due to vibration screws come
loose and can cause serious breakdown or injury.
9. Make sure no one is below when using the machine in high locations.
10. Keep hands well away from rotating parts.
11. During machine operation, cooling water must never be allowed to enter motor or other electrical
installation.
12. Should there be any leaking of water between synthetic ring and gearbox, stop immediately and
have the fault rectified by an authorised service workshop.
13. Overhead (upward) drilling can only be carried out with the use of suitable protection shielding
(water collecting device).
14. After interrupt cutting, do not switch on the motor again unless core bit can rotate freely.
15. Avoid touching near dry-cut immediately after work process. Area can be very hot and cause
severe burns.
16. To avoid machine self-starting, always trigger-off the switch should power supply become
interrupted or plug accidentally withdrawn from the socket while motor is still running.
17. When coring manually, always use also auxiliary handle (side handle) and hold the machine
firmly with both hands.
18. Keep sure-footing and body balance at all times for better control of reaction torque.
ENGLISH
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita DBM 131 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita DBM 131 in the language / languages: English, German, Dutch, Danish, French, Italian, Spanish as an attachment in your email.

The manual is 2,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info