690510
11
Zoom out
Zoom in
Previous page
1/21
Next page
11 ENGLISH
Lighting up the lamp
CAUTION: Do not look in the light or see the
source of light directly.
►Fig.5:
1. ON/speed change button 2. OFF button 3. Lamp
To turn on the lamp, push the ON/speed change button.
Push the OFF button to turn off the lamp. During the
tool actuating, the lamp turns on.
When the remaining battery capacity gets low, the lamp
starts blinking.
NOTE: The timing, at which the lamp starts blinking,
depends on the temperature at work place and the
battery cartridge conditions.
ASSEMBLY
CAUTION: Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Type of lter
Normal lter
►Fig.6: 1. Capsule 2.Prelter3. Filter
High performance lter
►Fig.7: 1. Capsule 2.Highperformancelter
Disposing of dust
CAUTION: Empty the cleaner before it
becomes too full, or the suction force weakens.
CAUTION: Be sure to empty the inside of the
cleaner itself of dust. Failure to do so may cause the
ltertobecloggedorthemotortobedamaged.
Disposing of dust for normal lter
Inordertodropduststickingonthelterinthecapsule,
tap the capsule 4 or 5 times with your hand.
►Fig.8: 1. Capsule 2. Suction inlet
Point the suction inlet downwards, turn the capsule in direction of the
arrow as illustrated, and disconnect the capsule slowly and straight.
►Fig.9: 1. Capsule 2. Suction inlet
NOTE:
Be sure to set a garbage bag beneath the cap-
sule, as dust may spill out when the capsule is opened.
Remove accumulated dust from inside of the capsule
andoffoftheprelter.
►Fig.10: 1.Prelter2. Capsule
Twisttheprelterindirectionofthearrowtounfastenthe
securinglipfromthecleanerunitandthenpullofftheprelter.
►Fig.11: 1.Prelter2. Securing lip
Cleanoutnedustfromtheprelter.Andthen,pulloff
thelterandlightlytapittoremovedust.
►Fig.12: 1. Filter 2.Prelter
Disposing of dust for high
performance lter
Inordertodropduststickingonthelterinthecapsule,
tap the capsule 4 or 5 times with your hand.
Now point suction inlet downwards, turn capsule in
direction of arrow in diagram, and disconnect capsule
slowly and straight.
►Fig.13: 1. Capsule 2. Suction inlet
NOTE: Dust may spill out when capsule is opened, so
be sure to set a garbage bag beneath capsule.
Remove accumulated dust from inside of capsule and
offofhighperformancelter.
►Fig.14: 1. Capsule 2.Highperformancelter
Twisthighperformancelterindirectionofarrowto
unfasten securing lip from cleaner unit and then pull off
thelter.
►Fig.15: 1. Securing lip
Cleanoutthenedustandlightlytaptodislodgedust
fromhighperformancelter.
Reassembly
Reassembly for normal lter
Putonthelterfullyinpositiononthecleanerunit.
►Fig.16: 1. Filter
NOTICE: Make sure the lter is put on straight
without being peeled back.Ifthelterisputon
incorrectly as illustrated, dust will get into the motor
housing, and cause a motor failure.
►Fig.17: 1. Filter
Installtheprelter.Atthistime,makesuretotwistthe
preltersothatthesecuringlipisrmlylockedinthe
cleaner unit.
►Fig.18: 1.Prelter2. Securing lip
►Fig.19
Install the capsule. Align the mark on the capsule with
themarknearthehandleandthenrmlytwistthecap-
sule in direction of the arrow until it is secured.
►Fig.20: 1. Mark
►Fig.21: 1. Capsule 2. Handle 3. Mark
NOTE: Always remove dust ahead of time, as the
suction power will be reduced if there is too much
dust in the cleaner.
NOTICE: Always be sure to check that both the
lter and prelter are loaded correctly prior to
using the cleaner. If they are not loaded correctly,
dust will get into the motor housing, and cause a
motorfailure.Ifthefollowingexamplesoccur,thelter
andprelterarenotloadedcorrectly.Reloadthem
correctly to rectify problem.
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita CL108FD at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita CL108FD in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 3,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info