Manual Makita CL072D (page 8 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

600674

Zoom out

Zoom in

1/52

– Wet dirt, water, oil or the like

– Hard pieces with sharp edges, such as wood

chips, metals, stones, glasses, nails, pins or

razors

– Powder to clot such as cement or tonor

– Conductive dust such as metal or carbon

– Fine particle like concrete dust

Such action may cause fire, injury and/or prop-

erty damage.

3. Stop operation immediately if you notice

anything abnormal.

4. If you drop or strike the cleaner, check it

carefully for cracks or damage before operation.

5. Do not bring close to stoves or other heat

sources.

6. Do not block the intake hole or vent holes.

SAVE THESE INSTRUCTIONS.

ENC007-6

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all instruc-

tions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using bat-

tery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may

result in a risk of overheating, possible burns

and even an explosion.

4. If electrolyte gets into your eyes, rinse them out

with clear water and seek medical attention right

away. It may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any conduc-

tive material.

(2) Avoid storing battery cartridge in a container

with other metal objects such as nails, coins,

etc.

(3) Do not expose battery cartridge to water or

rain.

A battery short can cause a large current flow,

overheating, possible burns and even a break-

down.

6. Do not store the tool and battery cartridge in

locations where the temperature may reach or

exceed 50°C (122°F).

7. Do not incinerate the battery cartridge even if it

is severely damaged or is completely worn out.

The battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before completely

discharged.

Always stop tool operation and charge the bat-

tery cartridge when you notice less tool power.

2. Never recharge a fully charged battery cartridge.

Overcharging shortens the battery service life.

3. Charge the battery cartridge with room tempera-

ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-

tery cartridge cool down before charging it.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before adjusting or checking

function on the tool.

Installing or removing battery cartridge

For Model CL072D (Fig. 1)

For Model CL102D (Fig. 2)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the

cartridge.

• To insert the battery cartridge, hold it so that the battery

cartridge front shape fits to that of the battery

installment opening and slip it into place. Always insert

it all the way until it locks in place with a little click. If

not, it may accidentally fall out of the tool, causing

injury to you or someone around you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Battery protection system

The cleaner is equipped with the protection system,

which automatically cuts off the output power for its long

service life.

The cleaner stops during operation when the cleaner

and/or battery are placed under the following situation.

This is caused by the activation of protection system and

does not show the cleaner trouble.

• When the cleaner is overloaded:

At this time, release the switch trigger and remove

causes of overload and then pull the switch trigger

again to restart.

• When the remaining battery capacity gets low:

Recharge the battery cartridge.

Switch action (Fig. 3)

To start the cleaner, simply press the “HIGH/LOW” but-

ton. To switch off, press the “OFF” button. To change the

cleaner speed, press the “HIGH/LOW” button. The first

press on this button is for high speed and the second

press for low speed and then each press on this button

repeats the high/low speed cycle alternatively.

Battery power lamp (Fig. 4)

• When the remaining battery capacity gets low, the bat-

tery power lamp blinks.

• When the remaining battery capacity gets much lower,

the tool stops during operation and the battery power

lamp lights up for about ten seconds. At this time,

remove the battery cartridge from the tool and charge

it.

NOTE:

• The time at which the battery power lamp start blinking

or lighting up depends on the temperature at work

place and the battery cartridge conditions.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita CL072D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,99 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita CL072D Manual

Product: