Manual Makita BVC340 (page 7 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

600684

Zoom out

Zoom in

1/52

Switch action (Fig. 3)

To start the cleaner, simply press the “HIGH/LOW” but-

ton. To switch off, press the “OFF” button. To change the

cleaner speed, press the “HIGH/LOW” button. The first

press on this button is for high speed and the second

press for low speed and then each press on this button

repeats the high/low speed cycle alternatively.

ASSEMBLY

CAUTION:

• Always be sure that the cleaner is switched off and the

battery cartridge is removed before carrying out any

work on the cleaner.

• Any work with the battery cartridge being installed on

the cleaner may cause a personal injury or damage to

the objects around the cleaner.

Installing dust bag (Fig. 4, 5, 6 & 7)

Hold the square section of the dust bag joint and fit the

pins inside the dust bag joint to the notches in the dust

outlet of the cleaner and then insert and turn it clockwise

all the way until it stops.

At this time, make sure that the fastener part on the dust

bag faces upward.

NOTE:

• When the dust bag joint and the ring inside the dust

bag come off, install as follows.

(1) Align the dust bag joint with the seam of the dust

bag and install it so that its protrusion faces

upward.

(2) Tighten the ring inside the dust bag firmly so that

the pins and the ring are positioned as shown in

the figure.

Installing the shoulder strap (Fig. 8)

Attach one end hook of the shoulder strap onto the ring

in the front of the cleaner and thrust the other end of the

strap through the band of the dust bag and then attach

the other end hook as shown in the figure.

Adjusting the shoulder strap (Fig. 9)

To adjust the length of the shoulder strap, pull it out to

your desired length and pull the strap in the direction of

arrow as shown in the figure.

Connecting the hose (Fig. 10)

CAUTION:

• Do not force the hose to bend it and/or stamp it.

Forcing and/or stamping the hose may cause deforma-

tion or damage to the hose.

• Do not pull the hose to carry the cleaner. Pulling the

hose may cause deformation or damage to the hose.

Insert the “A” end of the hose to the suction opening of

the cleaner and turn it clockwise all the way until it locks.

Attach the cuff on the “B” end of the hose and then con-

nect it to the dust outlet of an power tool.

Replacing the front cuff (Fig. 11)

Change the front cuff of the hose according to the dust

outlet size of a power tool you use.

To remove the front cuff, hold the hose and turn it coun-

terclockwise.

To mount the front cuff, turn it clockwise and then screw it

in until it stops.

OPERATION

WARNING:

• Do not use the shoulder strap when working in a high

place.

• When using the cleaner as a stationary cleaner, place it

on a flat and stable surface.

Vacuum cleaner (Fig. 12 & 13)

When using the cleaner as a portable cleaner, cross-

hanging the shoulder strap before the breast is difficult to

drop the cleaner.

NOTE:

• Long cut-off decorative paper that may be produced by

plaster board cutting work depending on the conditions

of workpiece to be cut and that may be stuffed inside

the hose may cause the hose suction blocking. When

this occurs, change the cutting depth setting of power

tool to deeper depth, which will relieve the hose suction

blocking.

CAUTION:

• When the dust bag is just new, dust may come out of its

surface. Using it a few times will minimize the dust leak

from the surface.

Operation of the cleaner with a nozzle or a dust

bag being installed

WARNING:

• Always be sure that the cleaner is switched off and

the battery cartridge is removed before installing or

removing the nozzle or any other attachment on the

cleaner. Failure to switch off and remove the battery

cartridge may result in serious personal injury.

NOTE:

• Before the blower mode operation immediately after

the cleaner mode operation, remove all remaining dust

from the cleaner due to possible blow out of dust.

Using as a blower (Fig. 14)

Install the nozzle onto the outlet (air vent) without fail.

To install the nozzle, fit the pin protruding from the

inside of nozzle to one of the cleaner notches and

then turn the nozzle clockwise securely.

To remove the nozzle, turn counterclockwise and pull

it out.

Direct the top point of the cleaner and then switch

on.

Emptying the dust bag

WARNING:

• Always be sure that both the cleaner and a con-

nected power tool are switched off and the battery

cartridge is removed and the power tool, if corded

tool, is unplugged before installing or removing the

dust bag on the cleaner and emptying the dust bag

(made of cloth). Failure to switch off, remove the bat-

tery cartridge and unplug the connected power tool

may result in electric shock and serious personal injury.

• When the dust bag is about half full, remove the dust

bag from the cleaner and pull the fastener out. Empty

the dust bag of its contents, tapping it lightly so as to

remove particles adhering to the insides which might

hamper further collection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BVC340 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BVC340 Manual

Product: