Manual Makita BUX361 (page 6 of 17) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

507666

Zoom out

Zoom in

1/17

Battery/motor protection system

The battery cartridge and tool are provided with protection

devices that will automatically reduce or cut off power to

the tool when overload situations develop that may cause

damage to the tool or battery cartridge.

If the tool becomes overloaded but not locked up a

protector is provided to reduce the revolutions to protect

the motor. In this case the two indicator lamps described

in the table below do not light or blink.

All other protection functions can be identified by the

indicator lamps described in the table below. (Fig. 6)

010823

Battery remaining capacity indicator (only

for models with Battery BL3622A)

Battery BL3622A is equipped with the battery remaining

capacity indicator. (Fig. 7)

Press the CHECK button to indicate the battery remaining

capacity. The indicator lamps will then light for approx.

three seconds.

011713

• When only the lowermost indicator lamp (next to the

“E”) blinks, or when none of the indicator lamps light,

the battery capacity has run out, so the tool does not

operate. In these cases, charge the battery or replace

the empty battery with a fully charged one.

• When two or more indicator lamps do not light even

after charging is complete, the battery has reached the

end of its service life.

• When the upper two and lower two indicator lamps light

alternately, the battery may have malfunctioned.

Contact your local Makita authorized service center.

NOTE:

• The indicated capacity may be lower than the actual

level during use or immediately after using the tool.

• Depending on the conditions of use and the ambient

temperature, the indication may differ slightly from the

actual capacity.

ASSEMBLY

WARNING:

• Always be sure that the tool is switched off and

battery cartridge is removed before carrying out

any work on the tool. Failure to switch off and remove

the battery cartridge may result in serious personal

injury from accidental start-up.

• Never start the tool unless it is completely

assembled. Operation of the tool in a partially

assembled state may result in serious personal injury

from accidental start-up.

Installing the grip (Fig. 8)

Securely fit the barrier and grip onto the shaft pipe with

two screws and clamps.

Make sure that the spacer on the shaft pipe is located

between the grip and the hanger. Do not remove or shrink

the spacer.

CAUTION:

• Never install the grip on the label or joint.

NOTE:

• In some countries, the barrier and spacer are not

provided with the tool. In that case, align the handle to

Status Action to be taken

– Blinking

Battery power has been nearly

used up.

Replace the battery with fully charged one.

– Lighting On

Battery protector is shutting off

the power - battery power has

been used up.

Replace the battery with fully charged one.

Blinking –

Overload protector is shutting off

the power - the motor was locked.

Release the switch trigger and remove the

cause of the motor lock or overload. If the

cutting tool is locked by entangling weeds or the

like, always remove the battery cartridge before

clearing it.

Lighting On –

Overheat protector is shutting

off the power - overheating.

Rest the equipment for a while.

Blinking Blinking

Electric or electronic malfunction Ask your local authorized service center for

repairs.

Indicator lamps

Remaining capacity

Lighted Off Blinking

E F

70% to 100%

45% to 70%

20% to 45%

0% to 20%

Charge the battery.

The battery may

have malfunctioned.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BUX361 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BUX361 Manual

Product: