Manual Makita BUH650 (page 10 of 80) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

600694

Zoom out

Zoom in

1/80

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or

checking function on the tool.

Installing or removing battery cartridge

CAUTION:

• Hold the tool and the battery cartridge firmly when

installing or removing battery cartridge. Failure to

hold the tool and the battery cartridge firmly may cause

them to slip off your hands and result in damage to the

tool and battery cartridge and a personal injury. (Fig. 1)

• Always switch off the tool before insertion or removal of

the battery cartridge.

• To remove the battery cartridge, withdraw it from the

tool while sliding the button on the front of the cartridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If you can see the red part on

the upper side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Handle mounting positions (Fig. 2)

The handle can be rotated to either 90° left or right and

mounted either 45° or 90° position to fit your work needs.

First, pull the knob and rotate the handle clockwise or

counterclockwise in the direction of arrow as shown in the

figure. The handle will be locked in 45° position. The pull

the knob and rotate more. The handle will be locked in 90°

position.

CAUTION:

• Always make sure that the handle is locked in the

desired position before operation.

Switch action

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates

properly and returns to the “OFF” position when

released. (Fig. 3)

For your safety, this tool is equipped with a dual switching

system. To turn on the tool, press triggers A and B.

Release either one of the two pressed triggers to turn off.

The sequence of switching is unimportant as the tool only

starts when both switches are activated.

Speed change (Fig. 4)

The strokes per minute can be adjusted just by turning the

adjusting dial. This can be done even while the tool is

running. The dial is marked 1 (lowest speed) to 6 (full

speed).

Refer to the table below for the relationship between the

number settings on the adjusting dial and the strokes per

minute.

CAUTION:

• The speed adjusting dial can be turned only as far as 6

and back to 1. Do not force it past 6 or 1, or the speed

adjusting function may no longer work.

• The strokes per minute vary by the conditions of

battery cartridge and shear blades.

Battery protection system

The tool is equipped with the protection system, which

automatically cuts off the output power for its long service

life.

The tool may stop during operation when the tool and/or

battery are placed under the following situation. This is

caused by the activation of protection system and does

not show the tool trouble.

• When the tool is overloaded:

At this time, release the switch trigger and remove

causes of overload and then pull the switch trigger

again to restart. When the tool does not work even

after pulling the switch trigger, the battery power

auto-stop is still at work. Charge the battery cartridge

before use.

• When the remaining battery capacity becomes low:

Recharge the battery cartridge.

Battery remaining capacity indicator (only

for models with Battery BL3622A)

Battery BL3622A is equipped with the battery remaining

capacity indicator. (Fig. 5)

Press the CHECK button to indicate the battery remaining

capacity. The indicator lamps will then light for approx.

three seconds.

• When only the lowermost indicator lamp (next to the

“E”) blinks, or when none of the indicator lamps light,

the battery capacity has run out, so the tool does not

Number on adjusting dial Strokes per minute (min

-1

)

6 1,800

5 1,750

4 1,650

3 1,500

2 1,300

1 1,000

Indicator lamps

Remaining capacity

Lighted Off Blinking

E F

70% to 100%

45% to 70%

20% to 45%

0% to 20%

Charge the battery.

The battery may have

malfunctioned.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BUH650 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 2,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BUH650 Manual

Product: