Manual Makita BTL062 (page 6 of 40) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

598627

Zoom out

Zoom in

1/40

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool

housing on either side and then secure it with a screw.

To remove, loosen the screw and then take it out.

Adjusting the angle head

The angle head can be adjusted 360° (8 positions in 45-

degree increments). To adjust it, loosen the hex bolt and

remove the angle head.

Adjust the angle head to the desired position and reinstall

it so that the teeth on the housing will match up with the

grooves in the angle head. Then tighten the hex bolt to

secure the angle head. (Fig. 7 & 8)

Straight head and ratchet head

(Accessory)

Straight heads and ratchet heads are available as

optional accessories for various applications on the job.

(Fig. 9 & 10)

OPERATION

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the upper

side of the button, it is not locked completely.

Insert it fully until the red part cannot be seen. If not, it

may accidentally fall out of the tool, causing injury to

you or someone around you.

Hold the tool firmly and place the socket over the bolt or

nut. Turn the tool on and fasten for the proper fastening

time. (Fig. 11)

The proper fastening torque may differ depending upon

the kind or size of the bolt, the material of the workpiece to

be fastened, etc. The relation between fastening torque

and fastening time is shown in the figures. (Fig. 12 & 13)

NOTE:

• Hold the tool pointed straight at the bolt or nut.

• Excessive fastening torque may damage the bolt/nut or

socket. Before starting your job, always perform a test

operation to determine the proper fastening time for

your bolt or nut.

• If the tool is operated continuously until the battery

cartridge has discharged, allow the tool to rest for

15 minutes before proceeding with a fresh battery.

The fastening torque is affected by a wide variety of

factors including the following. After fastening, always

check the torque with a torque wrench.

1. When the battery cartridge is discharged almost

completely, voltage will drop and the fastening torque

will be reduced.

2. Driver bit or socket bit

• Failure to use the correct size driver bit or socket bit

will cause a reduction in the fastening torque.

• A worn socket (wear on the hex end or square end)

will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the class of

bolt are the same, the proper fastening torque will

differ according to the diameter of bolt.

• Even though the diameters of bolts are the same,

the proper fastening torque will differ according to

the torque coefficient, the class of bolt and the bolt

length.

4. The use of the universal joint or the extension bar

somewhat reduces the fastening force of the impact

wrench. Compensate by fastening for a longer period

of time.

5. The manner of holding the tool or the material of

driving position to be fastened will affect the torque.

6. Operating the tool at low speed will cause a reduction

in the fastening torque.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Sockets

• Extension bar

• Universal joint

• Bit adapter

• Various type of Makita genuine batteries and chargers

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 88 dB (A)

Sound power level (L

): 99 dB (A)

Uncertainty (K): 3 dB (A)

Wear ear protection.

Vibration

ENG900-1

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Model BTL062

Work mode: impact tightening of fasteners of the

maximum capacity of the tool

Vibration emission (a

): 14.5 m/s

Uncertainty (K): 2.0 m/s

Model BTL063

Work mode: impact tightening of fasteners of the

maximum capacity of the tool

Vibration emission (a

): 16.5 m/s

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BTL062 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,02 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BTL062 Manual

Product: