Manual Makita BTD062 (page 5 of 10) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

598604

Zoom out

Zoom in

1/10

OPERATING INSTRUCTIONS

Installing or removing battery cartridge (Fig.1)

• To remove the battery cartridge, withdraw it from the

tool while pressing the buttons on both sides of the car-

tridge.

• To insert the battery cartridge, align the tongue on the

battery cartridge with the groove in the housing and slip

it into place. Always insert it all the way until it locks in

place with a little click. If not, it may accidentally fall out

of the tool, causing injury to you or someone around

you.

• Do not use force when inserting the battery cartridge. If

the cartridge does not slide in easily, it is not being

inserted correctly.

Checking the remaining battery capacity (Fig. 2)

When charging

When the charging begins, the first (far left) indicator

lamp begins to flicker. Then, as charging proceeds, the

other lamps light, one after the other, to indicate the bat-

tery capacity.

When using

When the tool is switched on, the lamps will light to indi-

cate the remaining battery capacity. When the tool is

switched off, the light goes out automatically.

If the battery has not been used for a long time, or is

needed refresh charging, the orange lamp begins to

flicker.

Use Makita refreshing adapter to refresh the battery.

CAUTION:

A battery cartridge extracted from the charger that has

been unplugged with the battery cartridge inserted does

not work even if it is inserted in the tool. At this time,

recharge it for about five seconds before use.

Installing or removing bit (Fig. 3)

CAUTION:

Always be sure that the tool is switched off and the bat-

tery cartridge is removed before installing or removing

the bit.

Use only the driver bit or socket bit shown in the figure

below.

Do not use any other driver bit or socket bit.

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit.

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

If the bit is not inserted deep enough into the sleeve, the

sleeve will not return to its original position and the bit will

not be secured. In this case, try re-inserting the bit

according to the instructions above.

Switch action (Fig. 4)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the “OFF” position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release

the trigger to stop.

Reversing switch action (Fig. 5)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for counter-

clockwise rotation. When the reversing switch lever is in

the neutral position, the switch trigger cannot be pulled.

Auto-stop mechanism (Fig. 6)

The tool stops automatically after the battery capacity

reaches under 20% to prevent the lack of fastening

torque. (Red color lamp lights on.) Charge the battery or

use a new fully charged one.

Auto-stop setting for number of impacts

This tool has a convenient auto-stop mechanism that

allows you to preset the desired number of impacts in

terms of the application. The tool then stops automati-

cally after reaching the preset number of impacts.

1. Pulling the trigger, insert the battery cartridge. Keep

on pulling the trigger after inserting the battery car-

tridge. (The indicating lamp on the back of the tool

will flash about 10 times, then the lamp will keep

lighting up lit.) (Fig. 7)

2. Hit the tool housing around the grip once with a

screwdriver etc. (The indicating lamp will go out.)

(Fig. 8)

3. Release the trigger. (The indicating lamp will keep

lighting up lit for 0.5 seconds, then the lamp will go

out.) (Fig. 9)

4. Hit the tool housing preset number of first digit

except 0. (The indicating lamp will light up in green

color. Then, the light goes out. )

Example: When the preset number is 12, hit the tool

housing once.

5. Pull the trigger, then release it.

6. Hit the tool housing preset number of second digit

except 0. (The indicating lamp will light up in red

color. Then, the light goes out.)

Example: When the preset number is 12, hit the tool

housing two times.

7. Pull the trigger, then release the trigger. (The indicat-

ing lamp will light up.)

8. Remove the battery cartridge. (Presetting has fin-

ished.) (The indicating lamp will go out.)

CAUTION:

When you change the presetting, do the same procedure

as above 1 – 8.

12 mm

9 mm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BTD062 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BTD062 Manual

Product: