Manual Makita BTD044 (page 8 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598605

Zoom out

Zoom in

1/64

• When not operating the tool, always set the reversing

switch lever to the neutral position.

This tool has a reversing switch to change the direction

of rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

Turning on the lamp (Fig. 6)

CAUTION:

• Do not look in the light or see the source of light

directly.

Pull the switch trigger to light up the lamp. The lamp

keeps on lighting while the switch trigger is being pulled.

The light automatically goes out approximately

10 seconds after the switch trigger is released.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

Auto-Stop setting for number of impacts

This tool has a convenient auto-stop mechanism that

allows you to preset the desired number of impacts in

terms of the application. The tool then stops

automatically after reaching the preset number of

impacts.

Setting for number of impacts (Fig. 7)

1. Pull the switch trigger, and then release it.

2. Pull the switch trigger approximately 3 seconds

while pressing the indication button, and then

release the switch trigger and the indication button.

3. The lamp on the left side of the display blinks so that

the number of first digit can be changed by pressing

the button.

4. Press the button and choose the desired number.

The displayed number changes fast by keeping

pressing the button. To set the first digit, pull the

switch trigger and then release it.

5. The lamp on the right side of the display starts to

blink so that the number of second digit can be

changed.

6. Press the button and choose the desired number.

The displayed number changes fast by keeping

pressing the button. To set the second digit, pull the

switch trigger and then release it.

7. For the final setting, pull the switch trigger while

pressing the indication button. The number of

impacts is set at once.

To reconfigure the number of impacts, pull the trig-

ger without pressing the indication button so that

return to 3 above.

Confirming the current setting number

To check the current setting number, pull the trigger

once, release it and then press the indication button.

Relation between presetting number and action

003611

NOTE:

• Use presetting number as a guideline. To keep the fas-

tening torque, number of impacts changes automati-

cally by remaining battery capacity.

Indicating lamp (Fig. 8)

• After impacting preset numbers, the indicating lamp

lights in green color.

• The red color light will light on if the trigger is released

before the presetting number of impacts is achieved. It

indicates that the operation is incomplete.

• When auto-stop mechanism is working, the indicating

lamp lights red while the switch trigger is being pulled.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing driver bit or socket bit

Use only the driver bit or socket bit shown in the figure.

Do not use any other driver bit or socket bit. (Fig. 9)

For tool with shallow bit hole

006348

For tool with deep bit hole

011405

1. To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it

will go. Then release the sleeve to secure the bit.

(Fig. 10)

Presetting

number

Clockwise rotation

Counterclockwise

rotation

Auto-stop setting

does not work.

Auto-stop setting

does not work.

01–99

After impacting [num-

ber of impacts (pre-

setting number x 2) x

0.02] seconds.

Green color lamp

lights on.

Switch off before

impacting [number of

impacts (presetting

number x 2) x 0.02]

seconds.

Red color lamp lights

on.

Then, the lamp goes

out.

Auto-stop setting

does not work.

Indication lamp goes

out.

A= 12mm

B= 9mm

Use only these type of bit. Follow the

procedure (1).

(Note) Bit-piece is not necessary.

A= 17mm

B= 14mm

To install these types of bits, follow the

procedure (1).

A= 12mm

B= 9mm

To install these types of bits, follow the

procedure (2).

(Note) Bit-piece is necessary for

installing the bit.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BTD044 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BTD044 Manual

Product: