Manual Makita BTD 150 (page 5 of 52) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

598624

Zoom out

Zoom in

1/52

Installing or removing bit (Fig. 3)

CAUTION:

Always be sure that the tool is switched off and the battery

cartridge is removed before installing or removing the bit.

Use only the driver bit or socket bit shown in the figure below.

Do not use any other driver bit or socket bit.

To install the bit, pull the sleeve in the direction of the arrow

and insert the bit into the sleeve as far as it will go. Then

release the sleeve to secure the bit.

To remove the bit, pull the sleeve in the direction of the arrow

and pull the bit out firmly.

NOTE:

If the bit is not inserted deep enough into the sleeve, the

sleeve will not return to its original position and the bit will not

be secured. In this case, try re-inserting the bit according to

the instructions above.

Switch action (Fig. 4)

CAUTION:

Before inserting the battery cartridge into the tool, always

check to see that the switch trigger actuates properly and

returns to the ‘‘OFF’’ position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger. Release the

trigger to stop.

Reversing switch action (Fig. 5)

CAUTION:

•

Always check the direction of rotation before operation.

•

Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation before the

tool stops may damage the tool.

•

When not operating the tool, always set the reversing switch

lever to the neutral position.

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the Aside for

clockwise rotation or from the B side for counterclockwise

rotation. When the reversing switch lever is in the neutral

position, the switch trigger cannot be pulled.

Operation

CAUTION:

Always insert the battery cartridge all the way until it locks in

place. If you can see the red part on the upper side of the

button, it is not locked completely. Insert it fully until the red

part cannot be seen. If not, it may accidentally fall out of the

tool, causing injury to you or someone around you.

Screwdriving operation (Fig. 6)

Hold the tool firmly and place the point of the driver bit in the

screw head. Apply forward pressure to the tool to the extent

that the bit will not slip off the screw. Start the tool slowly and

then increase the speed gradually. Release the trigger just as

the screw bottoms out. The proper fastening torque differs

depending upon the kind or size of screws/bolts, the type of

materials to be fastened, etc. Refer to the table for the relation

between fastening time and wood screw size. (Material to be

fastened: Lauan)

NOTE:

•

Hold the tool pointed straight at the screw.

•

When driving wood screws, predrill pilot holes to make

driving easier and to prevent splitting of the workpiece. The

pilot holes should be slightly smaller than the wood screws

in diameter.

•

The size of wood screw which can be fastened with this tool

may differ depending upon the type of material to be

fastened. Always perform a test operation to determine the

size of wood screw.

MAINTENANCE

CAUTION:

Always be sure that the tool is switched off and the battery

cartridge is removed before carrying out any work on the tool.

Replacement of carbon brushes (Fig.7&8)

Replace carbon brushes when they are worn down to the limit

mark. Both identical carbon brushes should be replaced at the

same time.

To maintain product safety and reliability, repairs, mainte-

nance or adjustment should be carried out by a Makita

Authorized Service Center.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BTD 150 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BTD 150 Manual

Product: