598602
4
Zoom out
Zoom in
Previous page
1/40
Next page
4
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
Specifications may differ from country to country.
Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
ENE054-1
The tool is intended for pressing staples into construction
materials such as timbers.
ADDITIONAL SAFETY RULES
FOR TOOL ENB069-1
1. Always wear safety goggles or safety glasses with
side shield, and a full face shield when needed.
2. Do not point the ejection port at anyone in the
vicinity (especially his face). Keep hands and feet
away from the ejection port area.
3. Always remove the battery cartridge before
loading the staples, adjustment, inspection,
maintenance or after operation is over.
4. Make sure no one is nearby before operation.
Never attempt to drive staples from both the inside
and outside of wall at the same time. Staples may
rip through and/or fly off, presenting a grave
danger.
5. Watch your footing and maintain your balance
with the tool. Make sure there is no one below
when working in high locations.
6. Check walls, ceilings, floors, roofing and the like
carefully to avoid possible electrical shock, gas
leakage, explosions, etc. caused by stapling into
live wires, conduits or gas pipes.
7. Use only staples specified in this manual. The use
of any other staples may cause malfunction of the
tool.
8. Do not tamper with the tool or attempt to use it for
other than driving staples.
9. Do not operate the tool without staples. It shortens
the service life of the tool.
10. Stop driving operations immediately if you notice
something wrong or out of the ordinary with the
tool.
11. Never staple into any materials which may allow
the staple to puncture and fly through as a
projectile.
12. Never actuate the switch trigger and safety lever
at the same time until you are prepared to staple
workpieces. Allow the workpiece to depress the
safety lever. Never defeat its purpose by securing
the safety lever back or by depressing it by hand.
13. Never tamper with the safety lever. Check the
safety lever frequently for proper operations.
SAVE THESE INSTRUCTIONS.
IMPORTANT SAFETY
INSTRUCTIONS
ENC007-4
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively shorter,
stop operating immediately. It may result in a risk
of overheating, possible burns and even an
explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
1. Red part
2. Button
3. Battery cartridge
4. Trigger
5. Safety lever
6. Sub magazine
7. Locking lever
8. Staples
9. Main magazine
10. Groove
11. Hook
12. Screw
13. Nut
14. Front
15. Workpiece
16. Rear
17. Sight window
Model BST220 BST221
Staple width 10 mm 10 mm
Applicable staples length 10 mm - 22 mm 10 mm - 22 mm
Staple magazine capacity 84 pcs 84 pcs
Overall length 247 mm 251 mm
Net weight 2.3 kg 2.4 kg
Rated voltage D.C. 14.4 V D.C. 18 V
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BST221 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BST221 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info