Manual Makita bss610sfe (page 9 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian)

382437

Zoom out

Zoom in

1/60

To get clean cuts, keep your sawing line straight and your

speed of advance uniform. If the cut fails to properly follow

your intended cut line, do not attempt to turn or force the

tool back to the cut line. Doing so may bind the blade and

lead to dangerous kickback and possible serious injury.

Release switch, wait for blade to stop and then withdraw

tool. Realign tool on new cut line, and start cut again.

Attempt to avoid positioning which exposes operator to

chips and wood dust being ejected from saw. Use eye

protection to help avoid injury.

Rip fence (Guide rule) (Fig. 20)

The handy rip fence allows you to do extra-accurate

straight cuts. Simply slide the rip fence up snugly against

the side of the workpiece and secure it in position with the

screw on the front of the base. It also makes repeated

cuts of uniform width possible.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance.

Adjusting for accuracy of 90° and 45° cut

(vertical and 45° cut) (Fig. 21 & 22)

For Model BSS610

This adjustment has been made at the factory. But if it is

off, adjust the adjusting screws with a hex wrench while

inspecting 90° or 45° the blade with the base using a

triangular rule or square rule, etc.

Adjusting for accuracy of 90° cut (vertical

cut)

For Model BSS611

This adjustment has been made at the factory. But if it is

off, adjust the adjusting screws with a hex wrench while

inspecting 90° the blade with the base using a triangular

rule or square rule, etc.

Replacing carbon brushes

Remove and check the carbon brushes regularly. Replace

when they wear down to the limit mark. Keep the carbon

brushes clean and free to slip in the holders. Both carbon

brushes should be replaced at the same time. Use only

identical carbon brushes. (Fig. 23)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 24)

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be

performed by Makita Authorized Service Centers, always

using Makita replacement parts.

ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Saw blades

• Rip fence (Guide rule)

•Hex wrench 5

• Dust nozzle

• Various type of Makita genuine batteries and chargers

For European countries only

Noise and Vibration

ENG005-2

The typical A-weighted noise levels are

sound pressure level: 90 dB (A)

sound power level: 101 dB (A)

Uncertainty: 3 dB (A)

Wear ear protection.

The typical weighted root mean square acceleration value

is not more than 2.5 m/s

These values have been obtained according to EN60745.

EC-DECLARATION OF CONFORMITY

ENH102-7

Model; BSS610, BSS611

We declare under our sole responsibility that this product

is in compliance with the following standards of

standardized documents;

EN60745, EN55014 in accordance with Council

Directives, 2004/108/EC, 98/37/EC.

CE 2007

Tomoyasu Kato

Director

Responsible Manufacturer:

Makita Corporation

3-11-8, Sumiyoshi-cho, Anjo, Aichi, JAPAN

Authorized Representative in Europe:

Makita International Europe Ltd.

Michigan Drive, Tongwell, Milton Keynes, Bucks MK15

8JD, ENGLAND

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita bss610sfe in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 1,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita bss610sfe Manual

Product: