Manual Makita BPJ140 (page 9 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598594

Zoom out

Zoom in

1/60

NOTE:

• If you connect a Makita vacuum cleaner to your plate

joiner, more efficient and cleaner operations can be

performed.

OPERATION

How to make joints

WARNING:

• Always clamp the workpiece to the workbench before

each operation. (Fig. 14 & 15)

Corner Joint (Fig. 16, 17 & 18)

T-Butt Joint (Fig. 19, 20 & 21)

Miter Joint (Fig. 22 & 23)

Frame Joint (Fig. 24 & 25)

Edge-To-Edge Joint (Fig. 26 & 27)

To make joints, proceed as follows:

1. Fit the two workpieces together as they will appear

in the finished joint position.

2. Mark the center of the intended biscuit grooves on

the workpiece using a pencil.

NOTE:

• The center of grooves should be at least 50 mm from

the outer edge of the workpieces.

• Allow 100 mm – 150 mm between grooves in multiple

biscuit application.

3. For Corner Joint and T-Butt Joint only

Clamp the vertical workpiece to the workbench.

For Miter Joint only

Clamp one workpiece to the workbench with the

mitered edge facing up.

For Frame Joint and Edge-To-Edge Joint only

Clamp one workpiece to the workbench.

4. Set the depth of groove according to the size of bis-

cuit to be used. Refer to the table in the “Adjusting

the depth of groove” section.

5. Adjust the angle guide height so that the blade is

centered in the board thickness.

6. Align the center mark on the base with the pencil

line on the workpiece.

7. Switch on the tool and gently push it forward to

extend the blade into the workpiece.

8. Gently return the tool to the original position after the

adjusting screw reaches the stopper.

9. For Corner Joint and T-Butt Joint only

Clamp the horizontal workpiece to the workbench.

For Miter Joint only

Clamp the other workpiece to the workbench with

the mitered edge facing up.

For Frame Joint and Edge-To-Edge Joint only

Clamp the other workpiece to the workbench.

10. For Corner Joint only

Place the tool on the workpiece so that the blade is

facing down.

For T-Butt Joint only

Remove the angle guide from the tool. Place the tool

on the workpiece so that the blade is facing down.

11. Repeat the steps 6 – 8 to groove in the horizontal or

the other workpiece.

If you do not need to center the blade in the board thick-

ness, proceed as follows:

For Corner Joint, Miter Joint, Frame Joint and

Edge-To-Edge Joint only

• Remove the angle guide from the tool. Set the

fence at 90° for Corner Joint, Frame Joint and

Edge-To-Edge Joint or at 45° for Miter Joint.

• Follow steps 1 – 11 excluding steps 5 and 10

described above.

For T-Butt Joint only

• Fit the two workpieces together as they will appear

in the finished joint position.

• Lay the vertical workpiece on the horizontal one.

Clamp both workpieces to the workbench.

• Remove the angle guide from the tool.

• Follow the steps 2, 4, 6, 7, 8 and 11 described

above.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

The tool and its air vents have to be kept clean. Regularly

clean the tool’s air vents or whenever the vents start to

become obstructed. (Fig. 28)

Replacing carbon brushes

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes. (Fig. 29)

Insert the top end of slotted bit screwdriver into the notch

in the tool and remove the holder cap cover by lifting it

up. (Fig. 30)

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps. (Fig. 31)

Reinstall the holder cap cover on the tool.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Angle guide

•Dust bag

• Set plate

• Lock nut wrench

• Plate joiner blades

• Makita genuine battery and charger

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BPJ140 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BPJ140 Manual

Product: