407552
8
Zoom out
Zoom in
Previous page
1/72
Next page
8
Slide Battery:
9.6V: BH9033 | BH9033A | BH9020 | BH9020A
12V: BH1233 | BH1233C | BH1220C
14.4V: BH1433 | BH1420 | BL1430
18V: BL1830
24V: BH2433 | BH2420
The following tables indicate the operating time on a
single charge.
* Operating time may differ by the type of battery, charging or
operating conditions.
3-1. Installing or removing Slide
battery cartridge (Fig. 3)
To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Always insert it all the way until it locks in
place with a little click.
Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
To remove the battery cartridge, withdraw it from the
tool while sliding the button on the front of the cartridge
or pressing the buttons on both sides of the cartridge.
3-2. Installing or removing Cluster
battery cartridge (Fig. 4)
To insert the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place.
Do not use force when inserting the battery cartridge. If
the cartridge does not slide in easily, it is not being
inserted correctly.
To remove the battery cartridge, withdraw it from the
Job site radio.
4. Replace battery compartment locker.
5. Reduced power, distortion and a “stuttering sound” or
low battery sign that appears on the display are
all the signs that the main battery pack needs to
replace.
Note:
The battery pack can’t be charged via the supplied AC
power adaptor.
6. When low battery sign appears and an “E” keeps
on flashing is the time to replace the back up batteries.
Installing the Soft bended rod
antenna (Fig. 5)
Install the Soft bended rod antenna as show in the figure.
Using Supplied AC power adaptor
(Fig. 6)
Remove the rubber protector and insert the adaptor plug
into the DC socket on the front side of the radio. Plug the
adaptor into a standard mains socket outlet. Whenever
the adaptor is used, the battery pack are automatically
disconnected. The AC adaptor should be disconnected
from the main supply when not in use.
Note:
When your radio has any interference in AM band by its
adaptor, please move your radio away from its AC
adaptor over 30 cm.
Setting the clock
1. Clock can be set either when the radio is power on or
off.
2. Display will show “-: - -” when the back up batteries
are installed.
3. Long press the time set button for more than
2 seconds, display will flash time set symbol and
also the hour digit, followed by a beep.
4. Rotate Tuning control to set the required hour.
5. Press button to confirm hour setting, the minute
digit will flash.
6. Rotate Tuning control to set the required minute.
7. Press the button again to complete clock setting.
Operating the radio
This radio equips with three tuning methods – Scan
tuning, Manual tuning and Memory presets recall.
Scan Tuning
1. Press the Power button to turn on the radio.
2. Select the required waveband by pressing the Band
button. Make sure the rubber bended rod antenna has
been well placed for best FM reception. For AM (MW)
band, rotate the radio to get best signal. Try to avoid to
operate the radio next to computer screen and other
equipment which will cause interference to the radio.
3. Press and release Scan button (long press Scan
button more than 2 seconds will activate time setting),
LCD display will flash Scan symbol and the radio will
up search and stop automatically when it finds a radio
station,. Press the Scan button again to pick up the
found station.
Note:
A stereo symbol will appear on the display, if the
station found is a stereo station.
Battery
Capacity
Battery Cartridge•Voltage
Operating time*
(At Max. Volume)
9.6V 12V 14.4V 18V 24V
1.3 Ah
PA09
9120
PA12
1220
PA14
1420
PA18 Approx. 7 hour
1.5 Ah BL1815 Approx. 8 hour
2.0 Ah
9122
BH9020
BH9020A
1222
BH1220C
1422
BH1420
1822 BH2420 Approx. 11 hour
2.6 Ah 9134 1234 1434 1834 Approx. 13 hour
3.0 Ah 9135 1235
1435
BL1430
1835
BL1830
Approx. 16 hour
3.3 Ah
BH9033
BH9033A
BH1233
BH1233C
BH1433 BH2433 Approx. 17 hour
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita bmr 100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita bmr 100 in the language / languages: All languages as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita bmr 100

Makita bmr 100 User Manual - English, Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info