Manual Makita BHP454 (page 7 of 56) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

598485

Zoom out

Zoom in

1/56

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned halfway between the “1” side and, “2”

side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

Selecting the action mode (FIg. 6)

This tool employs an action mode change lever. Select

one of the three modes suitable for your work needs by

using this lever.

For rotation only, slide the lever so that it points toward

the mark on the tool body. For rotation with hammering,

slide the lever so that it points toward the mark on the

tool body. For rotation with clutch, slide the lever so that

the it points toward the mark on the tool body.

NOTE:

• When changing the position from “ ” to “ ”, it may

be a little difficult to slide the mode change lever. At this

time, switch on and run the tool for a second at the “ ”

position, then stop the tool and slide to your desired

position.

CAUTION:

• Always set the lever correctly to your desired mode

mark. If you operate the tool with the lever positioned

halfway between the mode marks, the tool may be

damaged.

Adjusting the fastening torque (FIg. 7)

The fastening torque can be adjusted in 16 steps by

turning the adjusting ring so that its graduations are

aligned with the arrow on the tool body. The fastening

torque is minimum when the number 1 is aligned with the

arrow, and maximum when the number 16 is aligned with

the arrow.

Before actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular application.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing side grip (auxiliary handle)

(FIg. 8)

Always use the side grip to ensure operating safety.

Insert the side grip so that the protrusions on the grip base

and steel band fit in between the grooves on the tool

barrel. Then tighten the grip by turning clockwise.

Installing or removing driver bit or drill bit

(FIg. 9)

Turn the sleeve counterclockwise to open the chuck jaws.

Place the bit in the chuck as far as it will go. Turn the

sleeve clockwise to tighten the chuck.

To remove the bit, turn the sleeve counterclockwise.

Installing bit holder (FIg. 10)

Fit the bit holder into the protrusion at the tool foot on

either right or left side and secure it with a screw.

When not using the driver bit, keep it in the bit holders.

Bits 45 mm long can be kept there.

Adjustable depth rod (FIg. 11)

The adjustable depth rod is used to drill holes of uniform

depth. Loosen the clamp screw, set to desired position,

then tighten the clamp screw.

Hook (FIg. 12)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool

housing on either side and then secure it with a screw.

To remove, loosen the screw and then take it out.

OPERATION

Hammer drilling operation (FIg. 13)

CAUTION:

• There is a tremendous and sudden twisting force

exerted on the tool/bit at the time of hole break-

through, when the hole becomes clogged with chips

and particles, or when striking reinforcing rods

embedded in the concrete. Always use the side grip

(auxiliary handle) and firmly hold the tool by both side

grip and switch handle during operations. Failure to do

so may result in the loss of control of the tool and

potentially severe injury.

First, slide the action mode change lever so that it points

to the marking. The adjusting ring can be aligned in any

torque levels for this operation. Be sure to use a tungsten-

carbide tipped bit. Position the bit at the desired location

for the hole, then pull the switch trigger. Do not force the

tool. Light pressure gives best results. Keep the tool in

position and prevent it from slipping away from the hole.

Do not apply more pressure when the hole becomes

clogged with chips or particles. Instead, run the tool at an

idle, then remove the bit partially from the hole. By

repeating this several times, the hole will be cleaned out

and normal drilling may be resumed.

Blow-out bulb (optional accessory)

(FIg. 14)

After drilling the hole, use the blow-out bulb to clean the

dust out of the hole.

Screwdriving operation

First, slide the action mode change lever so that it points

to the marking. Adjust the adjusting ring to the proper

torque level for your work. Then proceed as follows.

Place the point of the driver bit in the screw head and

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the switch trigger

as soon as the clutch cuts in.

NOTE:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BHP454 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BHP454 Manual

Product: