381192

Makita bft123fz Manual

7
Zoom out
Zoom in
Previous page
1/76
Next page
7
Reversing switch action (Fig. 5)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.
Lighting up the lamps (Fig. 6)
CAUTION:
• Do not look in the light or see the source of light
directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The light automatically goes out 10 seconds after the
switch trigger is released.
NOTE:
• Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower
the illumination.
LED indicator (Fig. 7)
The lamp on the tool shows the following functions.
Function Status
Status of
the LED indicator/beeper
Action to be taken
LED indicator Beeper
Auto-stop
fastening
This function works when the tool has
reached the preset fastening torque
and normal tightening has been com-
pleted. This helps overtightening to be
avoided.
Lights up in
green for
approximately
one second.
__ __
Delayed re-start
For approximately one second after
auto-stop fastening, the tool does not
start even if the switch trigger is pulled.
Warning against
insufficient fasten-
ing
Insufficient fastening has been per-
formed when the switch trigger has
released before reaching the preset fas-
tening torque.
Lights up in
red.
A long beep Retighten the screw.
Warning for bat-
tery cartridge
capacity
This indicates the appropriate time to
replace the battery cartridge when the
battery power becomes low.
Flickers in red
slowly.
A series of
long beeps
Replace the battery
with fully charged
one.
Checking the
remaining battery
capacity,
Autostop
This function works when the battery
power is almost used up. At this time,
tool stops immediately.
Lights up in
red.
A long beep
Replace the battery
with fully charged
one.
Check the LED
indicator, light and
beeper operation
This function works to check the proper
operation of the LED indicator, light
and beeper when a battery cartridge
has been inserted into the tool.
Lights up first
in green, next
red.
(And then the
light comes
on.)
A series of
very short
beeps
__
Anti-reset of
controller
This function works when an abnormal
drop of the battery voltage occurs for
some reason, and the tool stops.
Flickers in red
and green
alternatively.
A series of
short beeps
Replace the battery
with fully charged
one.
Overheat
This function works when the tempera-
ture of the controller goes up very
highly, and the tool stops.
Flickers in red
quickly.
A series of
short beeps
Remove the battery
cartridge immedi-
ately and cool the tool
down.
Operation error of
the switch trigger
This function works to avoid the tool’s
immediate start upon insertion of bat-
tery cartridge into the tool with the
switch trigger being pulled.
Flickers in red
and green
alternatively.
A series of
short beeps
Release the switch
trigger.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita bft123fz at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita bft123fz in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita bft123fz

Makita bft123fz User Manual - English, Dutch - 14 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info