Manual Makita BFT044F (page 7 of 15) (English, Dutch)

598467

Zoom out

Zoom in

1/15

5. Use an optional adjusting grip to adjust the fastening

torque. Insert the pin of the adjusting grip into the hole

in the front of the tool. And then, turn the adjusting grip

clockwise to set a greater fastening torque, and coun-

terclockwise to set a smaller fastening torque.

6. Align the yellow line with your desired number on the

fastening torque scale.

7. Insert the battery cartridge and be sure that a fasten-

ing torque has been set up by using a fastening torque

tester.

8. Rotate the ring in front of the tool and then tighten the

screw to secure the ring.

NOTE:

• Numbers on the fastening torque scale is a guideline to

set up your desired fastening torque.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before carrying out any work

on the tool.

Installing or removing driver bit or socket bit

(Fig. 9 & 10)

Use only the driver bit or socket bit shown in the figure.

Do not use any other driver bit or socket bit.

To install the bit, pull the sleeve in the direction of the

arrow and insert the bit into the sleeve as far as it will go.

Then release the sleeve to secure the bit.

To remove the bit, pull the sleeve in the direction of the

arrow and pull the bit out firmly.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and the

bit will not be secured. In this case, try re-inserting the

bit according to the instructions above.

OPERATION

Screwdriving operation (Fig. 11)

Place the point of the driver bit in the screw head and

apply pressure to the tool. Then switch the tool on. When

the clutch cuts in, the motor will stop automatically. Then

release the switch trigger.

NOTE:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

Limits of fastening capacity

Use the tool within the range of the revolution angle up to

360°. If you use the tool beyond the upper limit of this

range, the clutch does not work. And the tool cannot

deliver enough fastening torque (LED indicator flickers in

red and green alternatively).

NOTE:

• The revolution angle means the angle which a screw/

bolt revolves when the tool attains to 100% from 50%

of desired torque.

• Use of a low temperature conditioned battery cartridge

may sometimes give warning for battery cartridge

capacity by warning lamp and beeper which makes the

tool stop immediately. In this case, the fastening capac-

ity may be inferior to the specification on this manual

even if a charged battery cartridge is used.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the bat-

tery cartridge is removed before attempting to perform

inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

Replacing carbon brushes (Fig. 12 & 13)

Remove and check the carbon brushes regularly.

Replace when they wear down to the limit mark. Keep

the carbon brushes clean and free to slip in the holders.

Both carbon brushes should be replaced at the same

time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take

out the worn carbon brushes, insert the new ones and

secure the brush holder caps.

To maintain product SAFETY and RELIABILITY, repairs,

any other maintenance or adjustment should be per-

formed by Makita Authorized Service Centers, always

using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

• Makita genuine battery and charger

• Adjust grip

•Protector

• Grip Base Set

• Grip 37

• Anti kickback head

NOTE:

• Some items in the list may be included in the tool pack-

age as standard accessories. They may differ from

country to country.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 70 dB (A) or less

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A)

Wear ear protection

ENG900-1

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: screwdriving without impact

Vibration emission (a

): 2.5 m/s

or less

Uncertainty (K): 1.5 m/s

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BFT044F in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,71 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita BFT044F

Makita BFT044F User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish - 60 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BFT044F Manual

Product: