Manual Makita BFT022F (page 6 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598466

Zoom out

Zoom in

1/60

LED indicator (Fig. 6)

The LED indicator on the tool shows the following functions.

013073

Adjusting the fastening torque (Fig. 7 & 8)

When you wish to drive machine screws, wood screws,

hex bolts, etc. with the predetermined torque, adjusting

the fastening torque as follows.

1. First remove the battery cartridge from the tool.

2. Loosen and remove the screw that secures ring.

3. Rotate the ring in the front of the tool by hand so that a

hole can be seen below the ring.

4. Place the battery cartridge in place and pull the switch

trigger. Release it so that the adjusting ring rotates

and becomes visible in the hole. And then remove the

battery cartridge.

Function Status

Status of the LED indicator/beeper

Action to be

taken

LED indicator Beeper

Auto-stop fastening

This function works when the tool has

reached the preset fastening torque

and normal tightening has been com-

pleted. This helps overtightening to

be avoided.

Lights up in

green for

approximately

one second.

——

Delayed re-start

For approximately one second after

auto-stop fastening, the tool does not

start even if the switch trigger is

pulled.

Warning against

insufficient fastening

Insufficient fastening has been per-

formed when the switch trigger has

released before reaching the preset

fastening torque.

Lights up in red. A long beep

Retighten the

screw.

Warning for battery

cartridge capacity

This indicates the appropriate time to

replace the battery cartridge when

the battery power becomes low.

Flickers in red

slowly.

A series of long

beeps

Replace the

battery with fully

charged one.

Checking the

remaining battery

capacity, Autostop

This function works when the battery

power is almost used up. At this time,

tool stops immediately.

Lights up in red. A long beep

Replace the

battery with fully

charged one.

Check the LED indi-

cator, lamp and

beeper operation

This function works to check the

proper operation of the LED indicator,

lamp and beeper when a battery car-

tridge has been inserted into the tool.

Lights up first in

green, next red.

(And then the

lamp comes

on.)

A series of very

short beeps

—

Anti-reset of control-

ler

This function works when an abnor-

mal drop of the battery voltage occurs

for some reason, and the tool stops.

Flickers in red

and green alter-

natively.

A series of short

beeps

Replace the

battery with fully

charged one.

Overheat

This function works when the temper-

ature of the controller goes up very

highly, and the tool stops.

Flickers in red

quickly.

A series of short

beeps

Remove the

battery car-

tridge immedi-

ately and cool

the tool down.

Operation error of

the switch trigger

This function works to avoid the tool’s

immediate start upon insertion of bat-

tery cartridge into the tool with the

switch trigger being pulled.

Flickers in red

and green alter-

natively.

A series of short

beeps

Release the

switch trigger.

Warning for limit of

the fastening capac-

ity

The tool automatically stops without

the clutch working when exceeding

the fastening capacity limit.

Flickers in red

and green alter-

natively.

A series of short

beeps

Remove the

battery car-

tridge and then

install it again.

Be sure to use

the tool under

load within its

capacity.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BFT022F in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita BFT022F

Makita BFT022F User Manual - English, Dutch - 15 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BFT022F Manual

Product: