598460

Makita BFT021F Manual

7
Zoom out
Zoom in
Previous page
1/14
Next page
7
Refresh charging
Refreshing adapter (optional accessory) can refresh an
inactive battery cartridge.
• Refresh charging should be done once a week.
• When you charge a new battery cartridge or a battery
cartridge that has not been used for a long time, it may
not accept a full charge. In this case, refresh charging
must be done. The battery cartridge may decrease the
tool performance, because the chemical substance of
the battery cartridge is inactive.
Checking the remaining battery capacity (Fig. 3)
For BH9020A and BH9033A
When charging
When the charging begins, the first (far left) indicating
lamp begins to flicker. Then, as charging proceeds, the
other lamps light, one after the other, to indicate the bat-
tery capacity.
When using
When the tool is switched on, the lamps will light after
2 seconds to indicate the remaining battery capacity.
When the tool is switched off, the light goes out.
If the battery has not been used for a long time, or is
needed refresh charging, the orange lamp begins to
flicker.
Use Makita refreshing adapter to refresh the battery.
CAUTION:
A battery cartridge extracted from the charger that has
been unplugged with the battery cartridge inserted does
not indicate the battery capacity due to its protective
function even if the tool is switched on after the battery
insertion into the tool. At this time, recharge it for about
five seconds before use.
NOTE:
Please contact Makita Authorized Service Center if the
warning lamp of the battery cartridge does not light up
when using or charging.
Switch action (Fig. 4)
CAUTION:
Before inserting the battery cartridge into the tool, always
check to see that the switch trigger actuates properly and
returns to the “OFF” position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
Reversing switch action (Fig. 5)
CAUTION:
• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation
before the tool stops may damage the tool.
• When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.
Lighting up the lamps (Fig. 6)
CAUTION:
Do not look in the light or see the source of light directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The light automatically goes out 11 seconds after the
switch trigger is released.
NOTE:
Use a dry cloth to wipe the dirt off the lens of lamp. Be
careful not to scratch the lens of lamp, or it may lower the
illumination.
LED indicator (Fig. 7)
The lamp on the tool shows the following functions.
Function Status
Status of
the LED indicator/beeper
Action to be taken
LED indicator Beeper
Auto-stop
fastening
This function works when the tool has
reached the preset fastening torque
and normal tightening has been com-
pleted. This helps overtightening to be
avoided.
Lights up in
green for
approximately
one second.
__ __
Delayed re-start
For approximately one second after
auto-stop fastening, the tool does not
start even if the switch trigger is pulled.
Warning against
insufficient fasten-
ing
Insufficient fastening has been per-
formed when the switch trigger has
released before reaching the preset fas-
tening torque.
Lights up in
red.
A long beep Retighten the screw.
Warning for bat-
tery cartridge
capacity
This indicates the appropriate time to
replace the battery cartridge when the
battery power becomes low.
Flickers in red
slowly.
A series of
long beeps
Replace the battery
with fully charged
one.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BFT021F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BFT021F in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita BFT021F

Makita BFT021F User Manual - English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info