598453

Makita BFL301F Manual

6
Zoom out
Zoom in
Previous page
1/48
Next page
6
LED indicator / Beeper (Fig. 5)
LED indicator / Beeper on the tool shows the following functions.
Status of
the LED indicator/beeper
Function Status Action to be taken
LED indicator Beeper
Lights up in
Green
Red
Blue
White in order.
A series of very
short beeps
Check LED, light
and beeper
(when pulling
switch trigger for
the first time after
installing a battery
cartridge into the
tool).
Make sure that green, red,
blue, white LED lights up
and beeper beeps properly.
__
Lights up in green
for approximately
one second.
__
Auto-stop
fastening
This function works when
the tool has reached the
preset fastening torque
and normal tightening has
been completed. This
helps overtightening to be
avoided.
__
Blinks in purple
slowly.
A series of long
beeps
Warning for battery
cartridge capacity
This indicates the
appropriate time to replace
the battery cartridge when
the battery power
becomes low.
Replace the battery
with fully charged one.
Lights up in purple. A long beep
Checking the
remaining battery
capacity, Autostop
This function works when
the battery power is almost
used up. At this time, tool
stops immediately.
Replace the battery
with fully charged one.
Lights up in red and
green alternatively.
A series of short
beeps
Anti-reset of
controller
This function works when
an abnormal drop of the
battery voltage occurs for
some reason and the tool
stops.
Replace the battery
with fully charged one.
Failure of motor
This function works when
motor fails.
Take it to a Makita
Authorized Service
centers.
Blinks in red quickly.
A series of short
beeps
Overheat
This function works when
the temperature of the
controller or motor goes up
very highly, and the tool
stops.
Remove the battery
cartridge immediately
and cool the tool
down.
Blinks in red and
yellow alternatively.
A long beep
Warning against
insufficient fasten-
ing
Fastening is incomplete
when switch trigger of tool
is released before clutch
activation.
__
Double-hitting
detection
This function works when
a screw is refastened after
fastening.
__
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BFL301F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BFL301F in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,24 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info