Manual Makita BDF456 (page 6 of 48) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

598444

Zoom out

Zoom in

1/48

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp. Be

careful not to scratch the lens of lamp, or it may lower

the illumination.

Reversing switch action (Fig. 5)

CAUTION:

• Always check the direction of rotation before operation.

• Use the reversing switch only after the tool comes to a

complete stop. Changing the direction of rotation

before the tool stops may damage the tool.

• When not operating the tool, always set the reversing

switch lever to the neutral position.

This tool has a reversing switch to change the direction of

rotation. Depress the reversing switch lever from the A

side for clockwise rotation or from the B side for

counterclockwise rotation.

When the reversing switch lever is in the neutral position,

the switch trigger cannot be pulled.

Speed change (Fig. 6)

CAUTION:

• Always set the speed change lever fully to the correct

position. If you operate the tool with the speed change

lever positioned halfway between the “1” side and “2”

side, the tool may be damaged.

• Do not use the speed change lever while the tool is

running. The tool may be damaged.

To change the speed, first switch off the tool and then

slide the speed change lever to the “2” side for high speed

or “1” side for low speed. Be sure that the speed change

lever is set to the correct position before operation. Use

the right speed for your job.

Adjusting the fastening torque (Fig. 7)

The fastening torque can be adjusted in 17 steps by

turning the adjusting ring so that its graduations are

aligned with the pointer on the tool body. The fastening

torque is minimum when the number 1 is aligned with the

pointer, and maximum when the marking is aligned with

the pointer.

The clutch will slip at various torque levels when set at the

number 1 to 16. The clutch is designed not to slip at the

marking.

Before actual operation, drive a trial screw into your

material or a piece of duplicate material to determine

which torque level is required for a particular application.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out any

work on the tool.

Installing or removing driver bit or drill bit

(Fig. 8)

Turn the sleeve counterclockwise to open the chuck jaws.

Place the bit in the chuck as far as it will go. Turn the

sleeve clockwise to tighten the chuck.

To remove the bit, turn the sleeve counterclockwise.

Hook (Fig. 9)

The hook is convenient for temporarily hanging the tool.

This can be installed on either side of the tool.

To install the hook, insert it into a groove in the tool

housing on either side and then secure it with a screw.

To remove, loosen the screw and then take it out.

Installing bit holder (Optional accessory)

(Fig. 10)

Fit the bit holder into the protrusion at the tool foot on

either right or left side and secure it with a screw.

When not using the driver bit, keep it in the bit holders.

Bits 45 mm long can be kept there.

OPERATION

CAUTION:

• Always insert the battery cartridge all the way until it

locks in place. If you can see the red part on the upper

side of the button, it is not locked completely. Insert it

fully until the red part cannot be seen. If not, it may

accidentally fall out of the tool, causing injury to you or

someone around you.

Hold the tool firmly with one hand on the grip and the

other hand on the bottom of the battery cartridge to

control the twisting action.

Screwdriving operation (Fig. 11)

CAUTION:

• Adjust the adjusting ring to the proper torque level for

your work.

Place the point of the driver bit in the screw head and

apply pressure to the tool. Start the tool slowly and then

increase the speed gradually. Release the switch trigger

as soon as the clutch cuts in.

CAUTION:

• Make sure that the driver bit is inserted straight in the

screw head, or the screw and/or bit may be damaged.

NOTE:

• When driving wood screws, predrill pilot holes to make

driving easier and to prevent splitting of the workpiece.

See the chart.

Drilling operation

First, turn the adjusting ring so that the pointer points to

the marking. Then proceed as follows.

Nominal diameter of wood

screw (mm)

Recommended size of pilot

hole (mm)

3.1 2.0 - 2.2

3.5 2.2 - 2.5

3.8 2.5 - 2.8

4.5 2.9 - 3.2

4.8 3.1 - 3.4

5.1 3.3 - 3.6

5.5 3.7 - 3.9

5.8 4.0 - 4.2

6.1 4.2 - 4.4

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BDF456 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,45 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BDF456 Manual

Product: