598439
20
Zoom out
Zoom in
Previous page
1/28
Next page
20
Readjusting the line of the 2-line trimmer head
The line length can be adjusted at any time with the best possible
results by tapping the line trimmer head on the ground lightly
during the mowing operation. The lengthening of the line amounts
to approx. 40 mm for each releasing operation.
The line blade cuts off projecting ends of the line automati-
cally.
Checking/replacing the line of the 2-line trimmer head
The new nylon line must be four meters long and have a dia-
meter of Ø 3.0 mm (order number, see extract from the spare
parts list).
To replace the line, it is advisable to dismantle the line trimmer
head rst (see instructions from section "Installing the 2-line
trimmer head" in chapter "Preparations" in reverse order).
1 Press in the cover mounting clips and open the line trim
-
mer head carefully (Caution! Inner spring presses the two
housing parts apart) (A).
2 Take the reel including the line out of the housing (B).
3 Remove remaining old pieces of line from the reel.
If there is still sufcient line on the reel, but if the
line does not adjust itself to the correct length
during the mowing operation, the line must be
wound up onto the reel again.
4 Use a paintbrush to clean the reel bottom side and the
housing and check for any signs of damage.
5 Kink the new line in the middle and insert into the partition
of the two reel guides as shown in the illustration (C, D).
6 Wind the line from the two reel guides in the direction of
the arrow tautly onto the reel (E).
7 Clamp both ends of the lines in two opposite grooves of the
reel so that the line does not slacken when the reel
is inserted into the housing (F).
8 Reinsert the reel into the bottom part of the housing and
thread both ends of the line into the line guides in the housing
(G).
9 Line up the reel according to the cut-outs in the top part of
the housing and press into the housing forcefully until
both snap-t closures snap into place (H).
Uneven line lengths are cut off by the line blade
on the cutter guard automatically during regular
operation.
BA
DC
FE
HG
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BCX3400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BCX3400 in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita BCX3400

Makita BCX3400 User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info