598439
17
Zoom out
Zoom in
Previous page
1/28
Next page
17
Starting
Move at least three meters away from the refueling
location in order to start the brushcutter!
To start the brushcutter, lay it down on a sufciently clear location
so that it is resting on its foot in stable position and the cutting
tool does not come into contact with anything else, neither with
the ground nor with other objects.
Cold starting
If there are any starting problems, excessi-
vely stored fuel could be the reason. Fuel
can only be stored for a limited period
of time and is subject to ageing!
Therefore, purchase only as much fuel as is sup-
posed to be consumed in a few months!
1 Push the short-circuit switch (
1) upward to "START".
2 Move the choke lever (
2) upward into -position (close
choke).
3 Press the fuel pump (
3) lightly approx. 7–10 times until there
are no more air bubbles to be seen in the fuel pump.
4 Hold the brushcutter rmly with one hand as shown in the
illustration.
5 Pull out the starter handle (
4) slowly until you can feel a
resistance.
The piston is now located just before the upper dead-center
position.
6 Now pull further
quickly and forcefully until the rst audible
ignition occurs.
The engine will start to run for a short time.
Do not pull out the starter handle more than 50
cm and do not let it y back; instead guide it back
slowly by hand.
7 Move the choke lever (2) downward into -position (open
choke).
8 Pull the starter handle again until the engine starts to run.
At idle (throttle lever (6) is not operated), the cutting
tool must not rotate. However, if the cutting tool
is rotating, the idle speed must be adjusted (see
section "Checking and adjusting the idle speed").
9 By grabbing the handle and pressing the safety locking
button (5) and the throttle lever slightly (6), bring the engine
up to medium speed and maintain that speed.
Never run the brushcutter under full load immedi-
ately; instead, let the engine warm up for approx.
three to ve minutes at medium speed.
10 With new machines, adjust the idle speed if necessary (see
section "Checking and adjusting the idle speed").
Warm starting
Start the brushcutter in warm condition, as described in the
section "Cold starting", but without opening the choke, i.e.
without putting the lever (2) into -position.
Turning off the engine
To turn off the engine, push the short-circuit switch (1) down-
ward to "STOP".
3 meters
1
4
2
5
6
3
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BCX3400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BCX3400 in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita BCX3400

Makita BCX3400 User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info