598439
13
Zoom out
Zoom in
Previous page
1/28
Next page
13
4-tooth star blade
To install the cutting tool, lay down the brushcutter so that it is
resting on its handle in stable position.
The tool you will require is the:
Combination wrench plus screwdriver as a handle
e.g. the medium-sized Allen key as an assembly pin
1 Place the mounting disk (
1) on the gearbox shaft (2) so
that one lateral cut-out (3) lines up with the cut-out (4) in
the angular gearbox.
2 Place the winding safety device (
5) on the angular gearbox
so that its lateral cut-out and the cut-out (4) in the angular
gearbox line up properly.
3 Insert the 4-tooth star blade (
6), pressure disk (7) and
ground glider (8) after one another onto the gearbox shaft
as shown in the illustration.
4 Insert the assembly pin (
9) through the mounting
disk into the cut-out of the angular gearbox.
The gearbox shaft is blocked.
5 Use the combination wrench (
10) to tighten the nut rmly
(left-hand thread).
The fastening nut (10) is equipped with a plastic
locking device and must be replaced, for safety
reasons, with a new fastening nut immediately
in the case of noticeable easy movement, but
no later than after the tool has been changed 10
times (see extract from the spare parts list)!
6 Remove the assembly pin again and check the cutting tool
for free movement.
2-line trimmer head
To install the cutting tool, lay down the brushcutter so that it is
resting on its handle in stable position.
The tool you will require is ,e.g, the medium-sized Allen key as
an assembly pin.
1 Place the mounting disk (
1) on the gearbox shaft (2) so
that the lateral drilled hole (3) lines up with the cut-out (4)
in the angular gearbox.
2 Place the winding safety device (
5) on the angular gearbox
so that its lateral cut-out and the cut-out (4) in the angular
gearbox line up properly.
3 Insert the assembly pin through the mounting
disk into the cut-out of the angular gearbox.
The gearbox shaft is blocked.
4 Screw on the 2-line trimmer head (
6) (left-hand thread) and
tighten rmly by hand.
5 Remove the assembly pin again and check the cutting tool
for free movement.
10
8
7
6
9
4
2
35
1
6
1
7
4
2
5
3
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BCX3400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BCX3400 in the language / languages: English as an attachment in your email.

The manual is 1,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita BCX3400

Makita BCX3400 User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info