598437
20
Zoom out
Zoom in
Previous page
1/28
Next page
20
Faden des 2-Fadenkopfes nachstellen
Die Fadenlänge kann während des Mähens durch ein leichtes
Auftippen mit dem Fadenkopf auf den Boden jederzeit optimal
eingestellt werden. Die Fadenverlängerung beträgt pro Entrie-
gelung ca. 40 mm.
Das Fadenmesser schneidet automatisch überstehende Fa-
denenden ab.
Faden des 2-Fadenkopfes kontrollieren/auswechseln
Der neue Nylonfaden muss vier Meter lang sein und einen
Durchmesser von Ø 2,4 mm haben (Bestellnummer siehe
Auszug aus der Ersatzteilliste).
Zum Auswechseln des Fadens empehlt es sich, zunächst den
Fadenkopf zu demontieren (siehe Anweisungen aus Abschnitt
"2-Fadenkopf montieren" in Kapitel "Vorbereitungen" in umge-
kehrter Reihenfolge).
1 Deckelaufnahmelaschen leicht eindrücken und Fadenkopf
öffnen (A).
2 Spule mit Faden aus dem Gehäuse herausnehmen (B).
3 Alte Fadenreste von der Spule entfernen.
Bendet sich noch ausreichend Faden auf der
Spule, stellt sich der Faden jedoch beim Mähen
nicht auf die richtige Länge ein, muss er neu
aufgewickelt werden.
4 Spulenunterseite und Gehäuse mit Pinsel reinigen und
auf evtl. Schäden prüfen.
6 Neuen Faden in der Mitte knicken und in die Spule einfädeln
(C, D).
7 Faden in Pfeilrichtung straff auf die Spule wickeln (E).
8 Beide Enden des Fadens in die Schlitze der Seilrolle klem
-
men, damit sich beim Einsetzen der Spule in das Gehäuse
der Faden nicht wieder entspannt (F).
9 Spule wieder in das Gehäuse einsetzen, dabei Fadenenden
durch die Fadenführungen stecken (G).
10 Spule und Gehäuse fest zusammenhalten und an beiden
Fadenenden ziehen, damit der Faden aus den Schlitzen
gezogen wird (H).
11 Spule nach den Gehäuseaussparungen ausrichten
und kräftig bis zum hörbaren Einrasten in das Gehäuse
drücken.
Ungleiche Fadenlängen werden während des
Betriebs durch das Fadenmesser an der
Schutzhaube automatisch abgeschnitten.
BA
DC
FE
HG
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BCX2500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BCX2500 in the language / languages: German as an attachment in your email.

The manual is 1,61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Makita BCX2500

Makita BCX2500 User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info