598436
4
Zoom out
Zoom in
Previous page
1/56
Next page
4
ENGLISH (Original instructions)
Explanation of general view
SPECIFICATIONS
Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
Specifications and battery cartridge may differ from country to country.
Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use ENE066-1
The tool is intended for cutting in mild steel and aluminum
only with appropriate saw blades.
General Power Tool Safety
Warnings GEA010-1
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
CORDLESS METAL CUTTER
SAFETY WARNINGS
GEB058-1
DANGER:
1. Keep hands away from cutting area and the blade.
Keep your second hand on auxiliary handle, or
motor housing. If both hands are holding the tool,
they cannot be cut by blade.
2. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the
workpiece.
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a stable
platform. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
5. Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring. Contact with a “live”
wire will also make exposed metal parts of the power
tool “live” and shock the operator.
6. When ripping always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance for blade binding.
7. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the tool
will run eccentrically, causing loss of control.
8. Never use damaged or incorrect blade washers or
bolts. The blade washers and bolt were specially
designed for your tool, for optimum performance and
safety of operation.
9. Causes and operator prevention of kickback;
- Kickback is a sudden reaction to a pinched, bound
or misaligned blade, causing an uncontrolled tool to
lift up and out of the workpiece toward the operator.
- When the blade is pinched or bound tightly by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the
operator.
- If the blade becomes twisted or misaligned in the
cut, the teeth at the back edge of the blade can dig
into the top surface of the workpiece causing the
blade to climb out of the kerf and jump back toward
the operator.
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be
avoided by taking proper precautions as given below.
1. Red part
2. Button
3. Battery cartridge
4. Lever
5. A position
6. Cutting line
7. Base
8. Switch trigger
9. Lock-off lever
10. Lamp
11. Shaft lock
12. Hex wrench
13. Hex bolt
14. Outer flange
15. Saw blade
16. Inner flange
17. Cup washer
18. Front grip
19. Rear handle
20. Sight grooves
21. Clamping screw
22. Rip fence (Guide rule)
23. Limit mark
24. Brush holder cap
25. Screwdriver
Model BCS550
Blade diameter 136 mm
Max. Cutting depth 51 mm
No load speed (min
-1
) 3,600
Overall length 348 mm
Net weight 2.6 kg
Rated voltage D.C. 18V
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita BCS550 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita BCS550 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info