Manual Makita BCG180 (page 8 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish)

598425

Zoom out

Zoom in

1/60

Insert the film type pack into the holder. (Fig. 17)

Attach the rubber ring, the nozzle and the holder cap.

Make sure holder cap is tightened firmly.

Push the rod gently until the piston touches the bottom of

the film type pack.

NOTE:

• Always check the film type pack for puncture or

damage before installing. Do not use damaged pack,

otherwise the tool may be damaged.

Direct filling

NOTICE:

• Make sure the piston C is attached to the rod. Do not

use other type of piston for direct filling.

• Direct filling can only be performed with the long holder

(600 ml).

Remove the holder cap, the nozzle and the rubber ring

from the holder.

Make sure the rod handle is placed at the most front

position.

Dip the mouth of the holder into the caulking material.

Pull the rod handle slowly until required amount of

caulking material is filled in the holder.

Attach the rubber ring, the nozzle and the holder cap.

Make sure holder cap is tightened firmly.

NOTICE:

• Clean the holder with appropriate solvent after every

day’s work. Otherwise adhered caulking material may

cause tool breakage.

OPERATION

CAUTION:

• Do not touch the rod during operation. Otherwise your

finger may be pinched between the rod and the

housing of the tool.

• Always wear goggles during operation.

NOTICE:

• Do not cover vents, or it may cause overheating and

damage to the tool.

• If you can not pull out the rod, turn the speed adjusting

dial to 1, and pull the switch trigger for a moment, and

try to pull the rod out after the motor stopped. If the rod

is still clogged, perform the same action until the rod is

able to move.

Cut off the tip of the nozzle suitable for individual

operation. Be careful how much you cut the nozzle. The

diameter of the nozzle affects the amount of caulking

material dispensed.

Pull the trigger to dispense caulking material.

The amount of the caulking material dispensed is

determined by the trigger, the speed adjusting dial, the

diameter of the nozzle opening, caulking material type,

and temperature.

It is recommended that the speed adjusting dial is set to

“1” and pull the trigger slowly at the first time to test how

much amount of caulking material is dispensed.

When the rod reaches front end, the motor starts idling.

Replace the caulking material when it happens.

NOTE:

If the caulking material is not dispensed, check the

following items:

• Nozzle tip is not cut adequately. Cut the nozzle tip

suitable for individual operation.

• Hardened material gets clogged in the nozzle. Remove

the hardened material.

• The cartridge is damaged. Replace the cartridge.

• Caulking material is stiff. Warm the material until it

becomes soft.

• The wrong piston is used. Use appropriate piston.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to

perform inspection or maintenance except for the

following troubleshooting related to the light.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may result.

• Clean the holder and the rod after every day’s work.

Keep them free from the adhesive material. Remove

the caulking material before it hardens. Remained

adhesive material may cause breakage of the tool.

To maintain product SAFETY and RELIABILITY, repairs,

carbon brush inspection and replacement, any other

maintenance or adjustment should be performed by

Makita Authorized Service Centers, always using Makita

replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are recommended

for use with your Makita tool specified in this manual.

The use of any other accessories or attachments might

present a risk of injury to persons. Only use accessory

or attachment for its stated purpose.

If you need any assistance for more details regarding

these accessories, ask your local Makita Service Center.

•Piston A

•Piston B

•Piston C

• Short holder (300 ml) set

• Long holder (600 ml) set

• Nozzle

• Safety goggles

• Makita genuine battery and charger

NOTE:

• Some items in the list may be included in the tool

package as standard accessories. They may differ

from country to country.

Noise

ENG905-1

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

): 70 dB (A) or less

Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A)

Wear ear protection.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita BCG180 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Turkish, Spanish as an attachment in your email.

The manual is 1,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita BCG180 Manual

Product: