598404
7
Zoom out
Zoom in
Previous page
1/64
Next page
7
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
Note: Specifications may differ from country to country.
Symbols
END106-2
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
............. Read instruction manual.
............. Wear safety glasses.
............. Do not use on scaffoldings, ladders.
Intended use
ENE059-1
The tool is intended for the preliminary interior work such
as fixing floor joists or common rafters and framing work in
2” x 4” housing.
IMPORTANT SAFETY
INSTRUCTIONS ENB113-1
WARNING: WHEN USING THIS TOOL, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
For personal safety and proper operation and
maintenance of the tool, read this instruction manual
before using the tool.
Always wear safety glasses to protect your eyes from
dust or screw injury.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
For Australia and New Zealand only
Always wear safety glasses and face shield to protect
your eyes from dust or screw injury. The safety glasses
and the face shield should conform with the
requirements of AS/NZS 1336.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
(Fig. 1)
Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or
rolled up. No necktie should be worn.
1. Safety glasses
2. Face shield
3. Deep
4. Shallow
5. Sunk too deeply (turn to raising
side)
6. Appropriate
7. Raised too high (turn to sink side)
8. Hook
9. Screw
10. Knob
11. Lever
12. Magazine cap
13. Screw channel
14. Lead screw
15. Feeding claw
16. Hammer
17. Bar
18. Screwdriver
19. Hex bolt
20. Hex wrench
21. Top cap
22. Top cap gasket
23. Top cap spacer
24. Piston assembly
25. Driver guide
26. Eyeleteer
27. Rubber ring (white)
28. Cutter knife
29. Pin
30. Piston cap
31. Driver bit
32. Piston
33. New driver bit
34. Hollowed side
35. Holes
36. Rubber ring
37. Drain cock
38. Air filter
39. Oiler
40. Pneumatic oil
41. Thinner
42. Stove
Model AR410HR
Air pressure 1.76 - 2.26 MPa (17.6 - 22.6 bar)
Screw length Coil type 25 - 41 mm
Screw capacity Sheet-collated 100 pcs
Safety Device Contact Arm System
Drive Adjustment Dial Type (Adjustment Range: 6mm)
Screw Feed Mechanism Feed Piston System
Min. hose diameter 5.0 mm
Dimensions (L X H X W) 296 mm X 116 mm X 305 mm
Net weight 1.9 kg
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita AR410HR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita AR410HR in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info