598400
33
Zoom out
Zoom in
Previous page
1/56
Next page
33
ESPAÑOL
Explicación de los dibujos
1 Salida de aire por minuto del
compresor
2 Frecuencia de clavado (veces/
minuto)
3 Regulador
4 Muy profundo
5A ras
6 Muy poco profundo
7 Gancho
8 Tornillo
9Agujero
10 Saliente
11 Adaptador de boca
12 Palanca de enganche
13 Puerta
14 Tornillo de ajuste
15 Placa de cambio
16 Flecha
17 Guía de clavos
18 Alimentador
19 Gatillo
20 Elemento de contacto
21 Pieza de trabajo
22 Palanca de cambio
23 Grosor de la pieza de trabajo
24 10 mm o más
25 Acero en forma de C
(Grosor 1,6 mm – 3,2 mm)
26 Longitud del clavo
27 Grosor de la madera
28 Rango del cemento 10 – 15 mm
29 Tapa
30 Grifo de drenaje
31 Filtro de aire
32 Aceitero
33 Aceite neumático
ESPECIFICACIONES
Debido a un programa continuo de investigación y
desarrollo, las especificaciones aquí dadas están suje-
tas a cambios sin previo aviso.
• Nota: Las especificaciones pueden ser diferentes de
país a país.
Uso previsto
La herramienta ha sido prevista para trabajo interior pre-
liminar, tal como fijación de viguetas al suelo o cabrios
comunes y trabajo de ensamblaje en viviendas 2” x 4”.
INSTRUCCIONES DE SEGURIDAD
IMPORTANTES
ADVERTENCIA:
CUANDO UTILICE ESTA HERRAMIENTA, DEBERÁ
OBSERVAR SIEMPRE LAS PRECAUCIONES DE
SEGURIDAD BÁSICAS PARA REDUCIR EL RIESGO
DE SUFRIR HERIDAS PERSONALES, INCLUYENDO
LO SIGUIENTE:
LEA TODAS LAS INSTRUCCIONES.
Por su propia seguridad y la utilización y el manteni-
miento apropiados de la herramienta, lea este manual
de instrucciones antes de utilizar la herramienta.
Póngase siempre gafas de seguridad para proteger
sus ojos del polvo o heridas producidas por los clavos.
ADVERTENCIA:
Es responsabilidad del patrón hacer cumplir al operario
y a otras personas cerca del área de trabajo el uso del
equipo de seguridad para la protección de los ojos.
Para Australia y Nueva Zelanda solamente
Póngase siempre gafas de seguridad y pantalla facial
para proteger sus ojos del polvo o heridas producidas
por los clavos. Las gafas de seguridad y la pantalla
facial deberán satisfacer los requisitos de las normas
AS/NZS 1336.
ADVERTENCIA:
Es responsabilidad del patrón hacer cumplir al operario
y a otras personas cerca del área de trabajo el uso del
equipo de seguridad para la protección de los ojos.
Utilice protección auditiva para proteger sus oídos con-
tra el ruido y protéjase también la cabeza. Póngase
también ropa ligera pero no holgada. Las mangas
deberán estar abotonadas o remangadas. No se
deberá utilizar corbata.
El hacer el trabajo deprisa o forzar la herramienta es
peligroso. Maneje la herramienta con cuidado. No uti-
lice la herramienta bajo la influencia de alcohol, drogas
o sustancias parecidas.
Directrices generales para el manejo de la herra-
mienta:
1. Asuma siempre que la herramienta contiene cla-
vos.
2. No se apunte asimismo ni a nadie con la herra-
mienta tanto si contiene clavos como si no.
Modelo AN711H
Presión de aire 1,28 – 2,26 MPa (12,8 – 22,6 bar)
Longitud del clavo
Clavos en bobina intercalada de alambre 45 mm – 75 mm
Clavos en bobina intercalada en lámina 38 mm – 65 mm
Número de clavos
Clavos en bobina intercalada de alambre
150 unidades, 200 unidades, 250 unidades, 300 unidades
Clavos en bobina intercalada en lámina
200 unidades
Diámetro mínimo de la manguera
5,0 mm
Dimensiones (La x An x Al) 293 mm x 125 mm x 288 mm
Peso neto 2,1 kg
Gafas de seguridad
Pantalla facial
33


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita AN711H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita AN711H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info