Manual Makita AN711H (page 9 of 56) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

598400

Zoom out

Zoom in

1/56

CAUTION:

• However when the tool is set to the “Intermittent Nail-

ing” mode, WITH THE TRIGGER HELD IN A HALF-

PULLED POSITION, an unexpected nailing could

occur, if contact element is allowed to re-contact

against the workpiece or the other surface under the

influence of recoil.

In order to avoid this unexpected nailing, perform as

follows;

A. Do not place the contact element against the work-

piece with excessive force.

B. Pull the trigger fully and hold it on for 1 – 2 seconds

after nailing.

• For No. (1) method, set the change lever to the

position.

• For No. (2) method, set the change lever to the

position.

After using the change lever to change the nailing

method, always make sure that the change lever is

properly set to the position for the desired nailing

method. (Fig. 14)

Nailing of steel plate (Fig. 15)

WARNING:

• Use 3.2 mm or less steel for C-shaped one.

The tool will bounce severely and a nail struck back,

causing serious injuries.

• Use hardened nails only for steel plate.

Using other purposed nails may cause serious injuries.

• When nailing, hold the tool so that it stands upright to

the driving surface.

Slanted nailing may cause nails to strike back, causing

serious injuries.

• When fastening a corrugated zinc plate on the C-

shaped steel, use 0.7 mm or less thick plate and

32 mm long hardened nails. Failure to do so may

cause nails to strike back, causing serious injuries.

• Do not use the tool for nailing on ceiling or roof.

Choose and use nails more than 10 mm longer than total

thickness of all workpiece to be fastened by referring to

the table below.

CAUTION:

• Depending on the hardness and total thickness of all

workpiece in combination to be fastened, enough fas-

tening may not be obtained. Nailing on steel plate to

excessive depth may extremely reduce the fastening

force. Before nailing, adjust the nailing depth properly.

• In the nailing on the steel plate, the driver may be

clogged due to susceptibility to wear. When it is worn,

sharpen it or replace it with a new one.

Nailing of concrete (Fig. 16)

WARNING:

• Use hardened nails only for concrete.

• Using other purposed nails may cause serious injuries.

Do not nail directly on the concrete or do not use to fas-

ten directly the steel plate to the concrete. Failure to do

so may cause concrete fragments to fly off or nails to

strike back, causing serious injuries.

• When nailing, hold the tool so that it stands upright to

the driving surface.

Slanted nailing may cause concrete fragments to fly off

or nails to strike back, causing serious injuries.

• Do not use on the surface that objects hang from, such

as area where hangers for sewer pipe, dust pipe etc.

are set up.

Choose and use nails so that the penetration amount into

concrete ranges 10 mm – 15 mm by referring to the table

below.

CAUTION:

• Use this tool only for soft concrete built up not so long

before. Using on the hard concrete may cause nail

bending or nailing to insufficient depth.

• When the penetration amount into concrete comes to

more than 15 mm, nailing to the sufficient length may

not be obtained.

Cutting off the sheet (Fig. 17)

CAUTION:

• Always disconnect the hose before cutting off the

sheet.

Tear off the output sheet in the direction of the arrow

when using the sheet collated nails.

MAINTENANCE

CAUTION:

• Always disconnect the air hose from the tool before

attempting to perform inspection or maintenance.

Jammed nailer (Fig. 18 & 19)

CAUTION:

• Always disconnect the air hose and remove the nails

from the magazine before cleaning a jam.

When the nailer becomes jammed, do as follows:

Open the magazine cap and remove the nail coil. Insert a

small rod or the like into the ejection port and tap it with a

hammer to drive out the nail jamming from the ejection

port. Reset the nail coil and close the magazine cap.

Drain tool

Remove the hose from the tool. Place the tool so that the

air fitting faces down to the floor. Drain as much as possi-

ble.

Cleaning of tool

Iron dust that adhere to the magnet can be blown off by

using an air duster.

Cap (Fig. 20)

When not in use, disconnect the hose. Then cap the air

fitting with the cap.

Storage

When not in use, the nailer should be stored in a warm

and dry place.

Material thickness

(mm)

C-shaped steel

(mm)

Nail length

(mm)

0–28

1.6 – 3.2

14 – 35 45

15 – 40 50

Wood thickness

(mm)

Nail length (mm)

Concrete range

(mm)

23 38 10 – 15

30 45 10 – 15

35 50 10 – 15

50 65 10 – 15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita AN711H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita AN711H Manual

Product: