Manual Makita AN634H (page 12 of 88) (English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish)

657977

Zoom out

Zoom in

1/88

12 ENGLISH

Single sequential actuation

Place the contact element against the workpiece and

pullthetriggerfully.

Afternailing,releasethecontactelement,andthen

release the trigger.

►Fig.24

CAUTION: Do not place the contact element

against the workpiece with excessive force. Also,

pull the trigger fully and hold it on for 1-2 seconds

after nailing.

Eveninthe“Singlesequentialactuation”mode,half-

pulledtriggercausesanunexpectednailing,whenthe

contact element re-contacts the workpiece.

Contact actuation

Pullthetriggerrstandthenplacethecontactelement

against the workpiece.

►Fig.25

Nailing on steel plate

WARNING: When nailing on the C-shaped

steel, limit the thickness to 2.3 mm (3/32″) or

thinner. Otherwise the tool will bounce severely and

anailstruckback,causingseriousinjuries.

WARNING: Use hardened nails only for steel

plate. Using other purposed nails may cause serious

injuries.

WARNING: When nailing, hold the tool so that

it stands upright to the driving surface. Slanted

nailingmaycausenailstostrikeback,causingseri-

ousinjuries.

WARNING: Do not use the tool for fastening

a corrugated plate or the C-shaped steel directly.

Itmaycausenailstostrikeback,causingserious

injuries.

WARNING: Do not use the tool for nailing on

ceiling or roof.

Chooseandusenails10mm(3/8″)ormuchlongerthan

totalthicknessofallworkpiecetobefastened.Referto

the table below.

Material thick-

ness including

C-shaped steel (A)

C-shaped steel (B)

thickness

Nail length (C)

9 mm - 22 mm

(11/32″-7/8″)

1.6 mm - 2.3 mm

(1/16″-3/32″)

32mm(1-1/4″)

10 mm - 27 mm

(3/8″-1-1/16″)

38mm(1-1/2″)

14 mm - 35 mm

(9/16″-1-3/8″)

45mm(1-3/4″)

15 mm - 40 mm

(5/8″-1-9/16″)

50mm(2″)

►Fig.26

NOTICE: Depending on the hardness and

total thickness of all workpiece in combination,

enough fastening may not be obtained. Nailing on

steel plate with excessive depth may extremely

reduce the fastening force.Beforenailing,adjust

the nailing depth properly.

NOTICE: Nailing on the steel plate makes the

driver prematurely worn out and it may cause nail

jamming.Whenthedriverisworn,replaceitwitha

new one.

Nailing on concrete

WARNING: Use hardened nails only for con-

crete. Using other purposed nails may cause serious

injuries.

WARNING: Do not nail directly on the con-

crete or do not fasten directly the steel plate to

the concrete.Itmaycauseconcretefragmentstoy

offornailstostrikeback,causingseriousinjuries.

WARNING: When nailing, hold the tool so that

it stands upright to the driving surface. Slanted

nailingmaycauseconcretefragmentstoyoffor

nailstostrikeback,causingseriousinjuries.

WARNING: Do not use the tool for fastening

an object to hang something such as sewer pipe.

Chooseandusenailssothatthepenetrationdepthinto

concreteranges10mm(3/8″)-15mm(5/8″).Referto

the table below.

Wood thick-

ness (A)

Nail length (B) Penetration depth

into concrete (C)

20mm(3/4″) 32mm(1-1/4″) Approx. 12 mm

(1/2″)

25mm(1″) 38mm(1-1/2″) Approx. 13 mm

(1/2″)

30mm(1-3/16″) 42mm/45mm

(1-5/8″/1-3/4″)

Approx.12mm/15

mm(1/2″/5/8″)

35mm(1-3/8″) 50mm(2″) Approx. 15 mm

(5/8″)

45mm(1-3/4″) 57mm(2-1/4″) Approx. 12 mm

(1/2″)

50mm(2″) 65mm(2-1/2″) Approx. 15 mm

(5/8″)

►Fig.27

NOTICE: Use the tool only for soft concrete

built up not so long before. Driving nails into hard

concretemaycausenailbendingornailingintoinsuf-

cientdepth.

NOTICE: When penetrating into concrete

deeper than 15 mm (5/8″), nails may not be driven

sufciently.

Cutting linked sheet

CAUTION: Always disconnect the air hose

from the tool before removing the linked sheet.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita AN634H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 17,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita AN634H Manual

Product: