Manual Makita AN634H (page 8 of 88) (English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish)

657977

Zoom out

Zoom in

1/88

8 ENGLISH

SAFETY WARNINGS

Pneumatic nailer/stapler safety

warnings

WARNING: WARNING Read all safety warn-

ings and all instructions.Failuretofollowthe

warningsandinstructionsmayresultinseriousinjury,

electricshockand/orre.

Save all warnings and instruc-

tions for future reference.

Forpersonalsafetyandproperoperationandmaintenanceof

thetool,readthisinstructionmanualbeforeusingthetool.

General safety

Do not permit those uninstructed to use the tool.

2. No horseplay. Respect the tool as a working

implement.

3. Do not operate when under the inuence of

alcohol, drugs or the like.

4. Never alter the tool.

Personal protective equipments

►Fig.1

1. Always wear safety glasses to protect your

eyes from dust or fastener injury.

WARNING: It is an employer's responsibility

to enforce the use of safety eye protection

equipment by the tool operators and by other

persons in the immediate working area.

For Australia and New Zealand only

Always wear safety glasses and face shield to

protect your eyes from dust or fastener injury.

Thesafetyglassesandthefaceshieldshould

conformwiththerequirementsofAS/NZS1336.

Wear hearing protection to protect your ears

against exhaust noise and head protection. Also

wear light but not loose clothing. Sleeves should be

buttoned or rolled up. No necktie should be worn.

Work area safety

1. Keep work area clean and well lit.Clutteredor

dark areas invite accidents.

2. Do not operate the tool in explosive atmo-

spheres, such as in the presence of ammable

liquids, gases or dust. Operating the tool can

createsparkswhichmayignitethedustorfumes.

Keep children and bystanders away while operating

the tool. Distractions can cause you to lose control.

4. Illuminate the work area sufciently.

There may be local regulations concerning noise

which must be complied with by keeping noise

levels within prescribed limits. In certain cases,

shutters should be used to contain noise.

Safety devices

1. Make sure all safety systems are in working

order before operation. Thetoolmustnotoper-

ateifonlythetriggerispulledorifonlythecontact

arm is pressed against the wood. It must work only

whenbothactionsareperformed.Testforpossible

faultyoperationwithfastenersunloadedandthe

pusherinfullypulledposition.

2. Do not play with the contact element: it pre-

vents accidental discharge, so it must be kept

on and not removed. Securing the trigger in the

ON position is also very dangerous. Never attempt

tofastenthetrigger.Donotoperateatoolifany

portionofthetooloperatingcontrolsisinoperable,

disconnected,altered,ornotworkingproperly.

3. Do not attempt to keep the contact element

depressed with tape or wire. Death or serious

injurymayoccur.

4. Always check contact element as instructed

in this manual. Fasteners may be driven acci-

dentallyifthesafetymechanismisnotworking

correctly.

Loading fasteners

1. Do not load the tool with fasteners when any

one of the operating controls is activated.

2. Use only fasteners specied in this manual.

Theuseofanyotherfastenersmaycausemal-

functionofthetool.

Power source

1. Never connect the tool to compressed air line

where the air pressure can exceed the suitable

air pressure range of the tool, specied in the

"SPECIFICATIONS" table, by 10%. Make sure

that the pressure supplied by the compressed air

system does not exceed the suitable air pressure

rangeofthetool.Settheairpressureinitiallyto

thelowervalueofthesuitableairpressurerange.

2. When using the tool operated by compressed

air, particular attention must be paid to avoid

exceeding the maximum allowable pressure.

3. Operate the tool at the lowest pressure

required for the application, in order to prevent

unnecessarily high noise levels, increased

wear and resulting failures.

4. Never use the tool with other than compressed

air.Ifbottledgas(carbondioxide,oxygen,

nitrogen,hydrogen,air,etc.)orcombustiblegas

(hydrogen,propane,acetylene,etc.)isusedasa

powersourceforthistool,thetoolwillexplodeand

causeseriousinjury.

5. Always disconnect the air hose and remove all

of the fasteners:

— when unattended;

— beforeperforminganymaintenanceor

repair;

— beforecleaningajam;

— beforemovingthetooltoanewlocation.

6. Use only pneumatic tool oil specied in this

manual.

Operational safety

1. Always check the tool for its overall condition

and loose screws before operation. Tighten as

required.

Handle the tool carefully, as there is high pressure

inside the tool that can be dangerous if a crack is

caused by rough handling (dropping or striking).

Do not attempt to carve or engrave on the tool.

3. Stop the operation immediately if you notice

something wrong or out of the ordinary with

the tool.Animproperlyfunctioningtoolmustnot

be used.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita AN634H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Portuguese, Spanish as an attachment in your email.

The manual is 17,49 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita AN634H Manual

Product: