Manual Makita AN620H (page 9 of 60) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

598399

Zoom out

Zoom in

1/60

Connecting air hose

Slip the air socket of the air hose onto the air fitting on the

nailer. Be sure that the air socket locks firmly into position

when installed onto the air fitting. A hose coupling must

be installed on or near the tool in such a way that the

pressure reservoir will discharge at the time the air sup-

ply coupling is disconnected.

OPERATION

CAUTION:

• Make sure all safety systems are in working order

before operation.

1. To drive a nail, you may place the contact element

against the workpiece and pull the trigger,

2. Pull the trigger first and then place the contact ele-

ment against the workpiece. (Fig. 12 & 13)

• No. (1) method is for intermittent nailing, when you wish

to drive a nail carefully and very accurately. No. (2)

method is for continuous nailing.

CAUTION:

• However when the tool is set to the “Intermittent Nail-

ing” mode, WITH THE TRIGGER HELD IN A HALF-

PULLED POSITION, an unexpected nailing could

occur, if contact element is allowed to re-contact

against the workpiece or the other surface under the

influence of recoil.

In order to avoid this unexpected nailing, perform as fol-

lows;

A. Do not place the contact element against the work-

piece with excessive force.

B. Pull the trigger fully and hold it on for 1 – 2 seconds

after nailing.

• For No. (1) method, set the change lever to the

position.

For No. (2) method, set the change lever to the

position.

After using the change lever to change the nailing

method, always make sure that the change lever is

properly set to the position for the desired nailing

method. (Fig. 14 & 15)

Nailing of steel plate (Fig. 16 & 17)

WARNING:

• Use 2.3 mm or less steel for C-shaped one.

The tool will bounce severely and a nail struck back,

causing serious injuries.

• Use hardened nails only for steel plate.

Using other purposed nails may cause serious injuries.

• When nailing, hold the tool so that it stands upright to

the driving surface.

Slanted nailing may cause nails to strike back, causing

serious injuries.

• When fastening a corrugated zinc plate on the C-

shaped steel, use 0.7 mm or less thick plate and

32 mm long hardened nails. Failure to do so may cause

nails to strike back, causing serious injuries.

• Do not use the tool for nailing on ceiling or roof.

Choose and use nails more than 10 mm longer than total

thickness of all workpiece to be fastened by referring to

the table below.

CAUTION:

• Depending on the hardness and total thickness of all

workpiece in combination to be fastened, enough fas-

tening may not be obtained. Nailing on steel plate to

excessive depth may extremely reduce the fastening

force. Before nailing, adjust the nailing depth properly.

• In the nailing on the steel plate, the driver may be

clogged due to susceptibility to wear. When it is worn,

sharpen it or replace it with a new one.

Nailing of concrete (Fig. 18)

WARNING:

• Use hardened nails only for concrete.

Using other purposed nails may cause serious injuries.

Do not nail directly on the concrete or do not use to fas-

ten directly the steel plate to the concrete. Failure to do

so may cause concrete fragments to fly off or nails to

strike back, causing serious injuries.

• When nailing, hold the tool so that it stands upright to

the driving surface.

Slanted nailing may cause concrete fragments to fly off

or nails to strike back, causing serious injuries.

• Do not use on the surface that objects hang from, such

as area where hangers for sewer pipe, dust pipe etc.

are set up.

Choose and use nails so that the penetration amount into

concrete ranges 10 mm – 15 mm by referring to the table

below.

CAUTION:

• Use this tool only for soft concrete built up not so long

before. Using on the hard concrete may cause nail

bending or nailing to insufficient depth.

• When the penetration amount into concrete comes to

more than 15 mm, nailing to the sufficient length may

not be obtained.

Cutting off the sheet (Fig. 19)

CAUTION:

• Always disconnect the hose before cutting off the

sheet.

Tear off the output sheet in the direction of the arrow

when using the sheet collated nails.

Air exhaust (Fig. 20)

Air exhaust direction can be changed easily by rotating

the exhaust cover. Change it when necessary.

Material thickness (mm) Nail length (mm)

10 – 27 38

15 – 30 45

15 – 38 50

Wood thickness

(mm)

Nail length (mm) Concrete (mm)

25 38 Approx. 13

30 45 Approx. 15

35 50 Approx. 15

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita AN620H in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,1 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita AN620H Manual

Product: