598396
6
Zoom out
Zoom in
Previous page
1/68
Next page
6
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
Note: Specifications may differ from country to country.
Symbols
END101-1
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
............. Read instruction manual.
............. Wear safety glasses.
Intended use
ENE059-1
The tool is intended for the preliminary interior work such
as fixing floor joists or common rafters and framing work
in 2 “x 4” housing.
IMPORTANT SAFETY
INSTRUCTIONS ENB090-2
WARNING: WHEN USING THIS TOOL, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED
TO REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
For personal safety and proper operation and
maintenance of the tool, read this instruction manual
before using the tool.
Always wear safety glasses to protect your eyes from
dust or nail injury.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or
rolled up. No necktie should be worn.
Rushing the job or forcing the tool is dangerous.
Handle the tool carefully. Do not operate when under
the influence of alcohol, drugs or the like.
General Tool Handling Guidelines:
(1) Always assume that the tool contains fasteners.
(2) Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
(3) Do not activate the tool unless the tool is placed
firmly against the workpiece.
(4) Respect the tool as a working implement.
(5) No horseplay.
(6) Do not hold or carry the tool with a finger on the
trigger.
(7) Do not load the tool with fasteners when any one
of the operating controls is activated.
(8) Do not operate the tool with any power source
other than that specified in the tool
operating/safety instructions.
An improperly functioning tool must not be used.
Sparks sometimes fly when the tool is used. Do not use
the tool near volatile, flammable materials such as
gasoline, thinner, paint, gas, adhesives, etc.; they will
ignite and explode, causing serious injury.
1. Compressor air output per minute
2. Nailing frequency (times/min)
3. Pneumatic tool oil
4. Adjuster
5. Hook
6. Contact element
7. Shingle guide
8. Shingle
9. Projection
10. Adjust plate
11. Lever
12. Magazine cap
13. Latch lever
14. Coil support plate
15. Graduation
16. Arrow
17. Feed Claw
18. Air fitting
19. Air socket
20. Trigger
21. Contact arm
22. Small rod
23. Ejection port
24. Nail
25. Humid
26. Hot
27. Brush
28. Drain cock
29. Air filter
30. Oiler
31. Pneumatic oil
32. Thinner
33. Stove
Model AN453
Air pressure 0.44 - 0.83 Mpa (4.4 - 8.3 bar)
Nail length 19 mm - 45 mm
Nail capacity 120 pcs.
Min. hose diameter 6.5 mm
Pneumatic tool oil Turbine oil
Dimensions (L X H X W) 265 mm X 269 mm X 117 mm
Net weight 2.4 kg
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita AN453 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita AN453 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info