598394
6
Zoom out
Zoom in
Previous page
1/52
Next page
6
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
Specifications may differ from country to country.
Weight according to EPTA-Procedure 01/2003
Intended use
ENE072-1
The tool is intended for securing a thin steel plate to the
concrete.
IMPORTANT SAFETY
INSTRUCTIONS ENB115-1
WARNING: WHEN USING THIS TOOL, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO
REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
1. For personal safety and proper operation and
maintenance of the tool, read this instruction manual
before using the tool.
2. Always wear safety glasses to protect your eyes from
dust or pin injury.
WARNING:
It is an employer’s responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
3. For Australia and New Zealand only
Always wear safety glasses and face shield to protect
your eyes from dust or pin injury. The safety glasses
and the face shield should conform with the
requirements of AS/NZS 1336.
WARNING:
It is an employer’s responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
(Fig. 1)
4. Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or
rolled up. No necktie should be worn.
5. Rushing the job or forcing the tool is dangerous.
Handle the tool carefully. Do not operate when under
the influence of alcohol, drugs or the like.
6. General Tool Handling Guidelines:
(1) Always assume that the tool contains fasteners.
(2) Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
(3) Do not activate the tool unless the tool is placed
firmly against the workpiece.
(4) Respect the tool as a working implement.
(5) No horseplay.
(6) Do not hold or carry the tool with a finger on the
trigger.
(7) Do not load the tool with fasteners when any one
of the operating controls is activated.
(8) Do not operate the tool with any power source
other than that specified in the tool operating/
safety instructions.
7. An improperly functioning tool must not be used.
8. Sparks sometimes fly when the tool is used. Do not
use the tool near volatile, flammable materials such as
gasoline, thinner, paint, gas, adhesives, etc.; they will
ignite and explode, causing serious injury.
9. The area should be sufficiently illuminated to assure
safe operations. The area should be clear and litter-
1. Safety glasses
2. Face shield
3. Compressor air output per minute
4. Nailing frequency
5. Adjuster
6. Too deep
7. Flush
8. Too shallow
9. Screw
10. Hook
11. Contact element
12. Nose adapter
13. LOCK position
14. FREE position
15. Latch lever
16. Door
17. Driver channel
18. Trigger
19. Workpiece
20. Thin steel plate
21. Penetration amount into concrete
22. Cap
23. Drain cock
24. Air filter
25. Oiler
26. Pneumatic oil
27. Thinner
28. Stove
Model AN250HC
Air pressure 1.18 - 2.26 MPa (11.8 - 22.6 bar)
Nail length
19 mm - 25 mm
Sheet-collated coil pin
Nail capacity 100 pcs
Min. hose diameter 5 mm
Dimensions (L X W X H) 295 mm X 128 mm X 291 mm
Net weight 2.1 kg
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita AN250HC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita AN250HC in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info