598391
7
Zoom out
Zoom in
Previous page
1/60
Next page
7
ENGLISH
Explanation of general view
SPECIFICATIONS
Due to our continuing programme of research and development, the specifications herein are subject to change without
notice.
Note: Specifications may differ from country to country.
Symbols END106-2
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
............. Read instruction manual.
............. Wear safety glasses.
............. Do not use on scaffoldings, ladders.
IMPORTANT SAFETY
INSTRUCTIONS ENB110-1
WARNING: WHEN USING THIS TOOL, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED
TO REDUCE THE RISK OF PERSONAL INJURY,
INCLUDING THE FOLLOWING:
READ ALL INSTRUCTIONS.
For personal safety and proper operation and
maintenance of the tool, read this instruction manual
before using the tool.
Always wear safety glasses to protect your eyes from
dust or nail injury.
WARNING:
It is an employer’s responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
For Australia and New Zealand only Always wear
safety glasses and face shield to protect your eyes
from dust or nail injury. The safety glasses and the face
shield should conform with the requirements of
AS/NZS 1336.
WARNING:
It is an employer's responsibility to enforce the use of
safety eye protection equipment by the tool operators
and by other persons in the immediate working area.
(Fig. 1)
Wear hearing protection to protect your ears against
exhaust noise and head protection. Also wear light but
not loose clothing. Sleeves should be buttoned or
rolled up. No necktie should be worn.
Rushing the job or forcing the tool is dangerous.
Handle the tool carefully. Do not operate when under
the influence of alcohol, drugs or the like.
General Tool Handling Guidelines:
(1) Always assume that the tool contains fasteners.
(2) Do not point the tool toward yourself or anyone
whether it contains fasteners or not.
(3) Do not activate the tool unless the tool is placed
firmly against the workpiece.
(4) Respect the tool as a working implement.
(5) No horseplay.
(6) Do not hold or carry the tool with a finger on the
trigger.
(7) Do not load the tool with fasteners when any one
of the operating controls is activated.
(8) Do not operate the tool with any power source
other than that specified in the tool operating/
safety instructions.
An improperly functioning tool must not be used.
Sparks sometimes fly when the tool is used. Do not use
the tool near volatile, flammable materials such as
1. Safety glasses
2. Face shield
3. Compressor air output per minute
4. Nailing frequency (times/min.)
5. Locking position
6. Released position
7. Lock lever
8. Trigger
9. Contact element
10. Adjuster
11. Too deep
12. Flush
13. Too shallow
14. Lock lever
15. Slide backward
16. Contact top cover
17. Hole
18. Protrusion
19. Nose adapter
20. Place first the contact element
against workpiece.
21. Hook
22. Hex wrench 3
23. Driver guide cover
24. Screw
25. Drain cock
26. Air filter
27. Oiler
28. Pneumatic oil
29. Thinner
30. Stove
Model AF500HP
Air pressure 0.98 - 2.26 MPa (9.8 - 22.6 bar)
Nail length 15 mm - 50 mm
Nail capacity 100 pcs.
Dimensions (L X H X W) 228 mm X 61 mm X 207 mm
Min. hose diameter 5.0 mm or more
Net weight 1.1 Kg
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita AF500HP at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita AF500HP in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info