390300

Makita 9565z Manual

4
Zoom out
Zoom in
Previous page
1/7
Next page
ENGLISH
Explanation of general view
1 Wheel cover
2 Bearing box
3 Screw
4 Press
5 Shaft lock
6 Lock nut
7 Depressed center wheel
8 Inner flange
9 Lock nut wrench
10 Switch lever
11 Exhaust vent
12 Inhalation vent
SPECIFICATIONS
9560Z 9561Z 9562Z 9563Z 9564Z 9565Z
Depressed center wheel diameter 100 mm 115 mm 125 mm 100 mm 115 mm 125 mm
Spindle thread M10 M14 M14 M10 M14 M14
No load speed (min
-1
) 11,000 11,000 11,000 11,000 11,000 11,000
Overall length 289 mm 289 mm 289 mm 299 mm 289 mm 299 mm
Net weight 1.7 kg 1.7 kg 1.7 kg 1.8 kg 1.8 kg 1.8 kg
•
Due to our continuing program of research and develop-
ment, the specifications herein are subject to change with-
out notice.
•
Note: Specifications may differ from country to country.
Power supply
The machine should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can only
be operated on single-phase AC supply. They are double-
insulated in accordance with European Standard and can,
therefore, also be used from sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
ADDITIONAL SAFETY RULES ENB031-4
1. Always use eye and ear protection. Other personal
protective equipment such as dust mask, gloves,
helmet and apron should be worn when necessary. If
in doubt, wear the protective equipment.
2. Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
3. Keep guards in place.
4. Use only wheels with correct size and wheels having
a maximum operating speed at least as high as the
highest No Load Speed marked on the tool’s name-
plate.When using depressed center wheels, be sure
to use only fiberglass-reinforced wheels.
5. Check the wheel carefully for cracks or damage
before operation. Replace cracked or damaged wheel
immediately.
6. Observe the instructions of the manufacturer for
correct mounting and use of wheels. Handle and
store wheels with care.
7. Do not use separate reducing bushings or adaptors
to adapt large hole abrasive wheels.
8. Use only flanges specified for this tool.
9. Do not damage the spindle, the flange (especially the
installing surface) or the lock nut. Damage to these
parts could result in wheel breakage.
10. For tools intended to be fitted with threaded hole
wheel, ensure that the thread in the wheel is long
enough to accept the spindle length.
11. Before using the tool on an actual workpiece, test run
the tool at the highest no load speed for at least 30
seconds in a safe position. Stop immediately if there
is any vibration or wobbling that could indicate poor
installation or a poorly balanced wheel. Check the
tool to determine the cause.
12. Check that the workpiece is properly supported.
13. Hold the tool firmly.
14. Keep hands away from rotating parts.
15. Make sure the wheel is not contacting the workpiece
before the switch is turned on.
16. Use the specified surface of the wheel to perform the
grinding.
17. Do not use cutting off wheel for side grinding.
18. Watch out for flying sparks. Hold the tool so that
sparks fly away from you and other persons or
flammable materials.
19. Pay attention that the wheel continues to rotate after
the tool is switched off.
20. Do not touch the workpiece immediately after opera-
tion; it may be extremely hot and could burn your
skin.
21. Position the tool so that the power cord always stays
behind the tool during operation.
22. If working place is extremely hot and humid, or badly
polluted by conductive dust, use a short-circuit
breaker (30 mA) to assure operator safety.
23. Do not use the tool on any materials containing
asbestos.
24. Do not use water or grinding lubricant.
25. Ensure that ventilation openings are kept clear when
working in dusty conditions. If it should become
necessary to clear dust, first disconnect the tool from
the mains supply (use non metallic objects) and avoid
damaging internal parts.
SAVE THESE INSTRUCTIONS.
4
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 9565z at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 9565z in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info