391336
20
Zoom out
Zoom in
Previous page
1/68
Next page
20
BETRIEB
WARNUNG:
Die Maschine darf auf keinen Fall gewaltsam ange-
drückt werden. Das Eigengewicht der Maschine übt
ausreichenden Druck aus. Gewaltanwendung und
übermäßiger Druck können zu einem gefährlichen
Schleifscheibenbruch führen.
Wechseln Sie die Schleifscheibe IMMER aus, falls die
Maschine während der Schleifarbeit fallen gelassen
wurde.
Eine Schleif- oder Trennscheibe darf NIEMALS gegen
das Werkstück geschlagen oder gestoßen werden.
Achten Sie besonders beim Bearbeiten von Ecken,
scharfen Kanten usw. darauf, dass die Schleifscheibe
nicht springt oder hängen bleibt. Dies könnte den Ver-
lust der Kontrolle und Rückschläge verursachen.
Verwenden Sie die Maschine NIEMALS mit Holz- und
anderen Sägeblättern. Solche Sägeblätter verursachen
bei Verwendung an einer Schleifmaschine häufiges
Rückschlagen und Verlust der Kontrolle, was zu Verlet-
zungen führen kann.
VORSICHT:
Schalten Sie die Maschine nach der Arbeit stets aus,
und warten Sie, bis die Schleifscheibe zum völligen
Stillstand gekommen ist, bevor Sie die Maschine able-
gen.
Schleif- und Schmirgelbetrieb (Abb. 10)
Halten Sie die Maschine IMMER mit einer Hand am
Gehäuse und mit der anderen am Seitengriff. Schalten
Sie die Maschine ein, und setzen Sie dann die Trenn-
oder Schleifscheibe an das Werkstück an.
Halten Sie die Trenn- oder Schleifscheibe im Allgemei-
nen in einem Winkel von etwa 15° zur Werkstückoberflä-
che.
Bewegen Sie die Schleifmaschine beim Einschleifen
einer neuen Schleifscheibe nicht in Richtung B, weil die
Schleifscheibe sonst in das Werkstück einschneidet.
Sobald die Schleifscheibenkante durch Gebrauch abge-
rundet ist, kann die Schleifscheibe sowohl in Richtung A
als auch in Richtung B bewegt werden.
Betrieb mit Trennschleifscheibe / Diamantscheibe (Sonderzubehör) (Abb. 11)
Die Montagerichtung der Sicherungsmutter und des Innenflansches hängt von der Scheibendicke ab.
Siehe die nachstehende Tabelle.
1
2
3
1
4
3
Trennschleifscheibe
Dicke: Weniger als 4 mm (5/32") Dicke: 4 mm (5/32") oder mehr
Diamantscheibe
100 mm (4")
Dicke: Weniger als 4 mm (5/32") Dicke: 4 mm (5/32") oder mehr
1. Sicherungsmutter
3. Innenflansch
4. Diamantscheibe2. Trennschleifscheibe
16 mm (5/8") 16 mm (5/8")
20 mm (13/16") 20 mm (13/16")
115 mm (4 - 1/2") / 125 mm (5")
1
2
3
1
4
3
Trennschleifscheibe Diamantscheibe
Dicke: 4 mm (5/32") oder mehr Dicke: Weniger als 4 mm (5/32") Dicke: 4 mm (5/32") oder mehrDicke: Weniger als 4 mm (5/32")
1. Sicherungsmutter
3. Innenflansch 4. Diamantscheibe2. Trennschleifscheibe
22,23 mm (7/8") 22,23 mm (7/8")
22,23 mm (7/8") 22,23 mm (7/8")
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 9565 hkd at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 9565 hkd in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 0,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info