Manual Makita 9558 nb (page 5 of 10) (English, German, Dutch, Danish, French, Italian, Norwegian)

390354

Zoom out

Zoom in

1/10

ENGLISH

Explanation of general view

1 Shaft lock

2 Switch lever

3 Wheel guard

4 Screw

5 Bearing box

6 Lock nut

7 Depressed center grinding

wheel/ Multi-disc

8 Inner flange

9 Lock nut wrench

10 Shaft lock

11 Exhaust vent

12 Inhalation vent

SPECIFICATIONS

Model 9556NB 9557NB 9558NB

Depressed center wheel diamiter ...........................100 mm 115 mm 125 mm

Spindle thread .......................................................M10 M14 M14

No load speed (min

-1

) ............................................11,000 11,000 11,000

Overall length ........................................................271 mm 271 mm 271 mm

Net weight ..............................................................1.6 kg 1.6 kg 1.6 kg

Safety class ........................................................... /II /II /II

• Due to our continuing program of research and devel-

opment, the specifications herein are subject to change

without notice.

• Note: Specifications may differ from country to country.

Intended use

The tool is intended for cutting, grinding and sanding of

metal and stone materials without the use of water.

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

Safety hints

For your own safety, please refer to the enclosed safety

instructions.

ADDITIONAL SAFETY RULES

ENB031-6

1. Always use eye and ear protection. Other per-

sonal protective equipment such as dust mask,

gloves, helmet and apron should be worn.

2. Always be sure that the tool is switched off and

unplugged before carrying out any work on the

tool.

3. Keep guards in place.

4. Use only wheels with correct size and wheels

having a maximum operating speed at least as

high as the highest No Load Speed marked on

the tool’s nameplate. When using depressed

center wheels, be sure to use only fiberglass-

reinforced wheels.

5. Check the wheel carefully for cracks or damage

before operation. Replace cracked or damaged

wheel immediately.

6. Observe the instructions of the manufacturer for

correct mounting and use of wheels. Handle and

store wheels with care.

7. Do not use separate reducing bushings or adap-

tors to adapt large hole abrasive wheels.

8. Use only flanges specified for this tool.

9. Do not damage the spindle, the flange (espe-

cially the installing surface) or the lock nut. Dam-

age to these parts could result in wheel

breakage.

10. For tools intended to be fitted with threaded hole

wheel, ensure that the thread in the wheel is long

enough to accept the spindle length.

11. Before using the tool on an actual workpiece,

test run the tool at the highest no load speed for

at least 30 seconds in a safe position. Stop

immediately if there is any vibration or wobbling

that could indicate poor installation or a poorly

balanced wheel. Check the tool to determine the

cause.

12. Check that the workpiece is properly supported.

13. Hold the tool firmly.

14. Keep hands away from rotating parts.

15. Make sure the wheel is not contacting the work-

piece before the switch is turned on.

16. Use the specified surface of the wheel to per-

form the grinding.

17. Do not use cutting off wheel for side grinding.

18. Watch out for flying sparks. Hold the tool so that

sparks fly away from you and other persons or

flammable materials.

19. Pay attention that the wheel continues to rotate

after the tool is switched off.

20. Do not touch the workpiece immediately after

operation; it may be extremely hot and could

burn your skin.

21. Position the tool so that the power cord always

stays behind the tool during operation.

22. If working place is extremely hot and humid, or

badly polluted by conductive dust, use a short-

circuit breaker (30 mA) to assure operator safety.

23. Do not use the tool on any materials containing

asbestos.

24. Do not use water or grinding lubricant.

25. Ensure that ventilation openings are kept clear

when working in dusty conditions. If it should

become necessary to clear dust, first disconnect

the tool from the mains supply (use non metallic

objects) and avoid damaging internal parts.

26. When use cut-off wheel, always work with the

dust collecting wheel guard required by domes-

tic regulation.

27. Cutting discs must not be subjected to any lat-

eral pressure.

SAVE THESE INSTRUCTIONS.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 9558 nb in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,19 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 9558 nb Manual

Product: