Manual Makita 9556HN (page 7 of 64) (English, German, Dutch, Danish, French, Italian, Portuguese, Spanish)

593088

Zoom out

Zoom in

1/64

Installing or removing wheel guard

(For depressed center wheel, multi disc /

abrasive cut-off wheel, diamond wheel)

For tool with locking screw type wheel guard

(Fig. 4 & 5)

WARNING:

• When using a depressed center grinding wheel/Multi-

disc, flex wheel, wire wheel brush, cut-off wheel or dia-

mond wheel, the wheel guard must be fitted on the tool

so that the closed side of the guard always points

toward the operator.

• When using an abrasive cut-off / diamond wheel, be

sure to use only the special wheel guard designed for

use with cut-off wheels. (In European countries, when

using a diamond wheel, the ordinary guard can be

used.)

Mount the wheel guard with the protrusion on the wheel

guard band aligned with the notch on the bearing box.

Then rotate the wheel guard to such an angle that it can

protect the operator according to work. Be sure to tighten

the screw securely.

To remove wheel guard, follow the installation procedure

in reverse.

Installing or removing depressed center grinding

wheel/Multi-disc (Fig. 6 & 7)

Mount the inner flange onto the spindle. Fit the wheel/

disc on the inner flange and screw the lock nut onto the

spindle.

To tighten the lock nut, press the shaft lock firmly so that

the spindle cannot revolve, then use the lock nut wrench

and securely tighten clockwise.

To remove the wheel, follow the installation procedure in

reverse.

WARNING:

• Only actuate the shaft lock when the spindle is not

moving.

OPERATION

WARNING:

• It should never be necessary to force the tool. The

weight of the tool applies adequate pressure. Forcing

and excessive pressure could cause dangerous wheel

breakage.

• ALWAYS replace wheel if tool is dropped while grind-

ing.

• NEVER bang or hit grinding disc or wheel onto work.

• Avoid bouncing and snagging the wheel, especially

when working corners, sharp edges etc. This can

cause loss of control and kickback.

• NEVER use tool with wood cutting blades and other

sawblades. Such blades when used on a grinder fre-

quently kick and cause loss of control leading to per-

sonal injury.

CAUTION:

• After operation, always switch off the tool and wait until

the wheel has come to a complete stop before putting

the tool down.

Grinding and sanding operation (Fig. 8)

ALWAYS hold the tool firmly with one hand on housing

and the other on the side handle. Turn the tool on and

then apply the wheel or disc to the workpiece.

In general, keep the edge of the wheel or disc at an angle

of about 15 degrees to the workpiece surface.

During the break-in period with a new wheel, do not work

the grinder in the B direction or it will cut into the work-

piece. Once the edge of the wheel has been rounded off

by use, the wheel may be worked in both A and B direc-

tion.

Operation with abrasive cut-off / diamond wheel (optional accessory) (Fig. 9)

The direction for mounting the lock nut and the inner flange varies by wheel thickness.

Refer to the table below.

1. Lock nut 2. Abrasive cut-off wheel 3. Inner flange 4. Diamond wheel

Abrasive cut-off wheel

Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more

Diamond wheel

100 mm (4")

Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more

16 mm (5/8") 16 mm (5/8")

20 mm (13/16") 20 mm (13/16")

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 9556HN in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 9556HN Manual

Product: