Manual Makita 9227 (page 6 of 18) (English, German, Dutch, Danish, French, Italian, Norwegian)

79032

Zoom out

Zoom in

1/18

OPERATING INSTRUCTIONS

Installing loop handle

Important:

Always be sure that the tool is switched off and

unplugged before installing the loop handle.

Always install the loop handle on the tool before

operation. Hold the tool’s switch handle and the loop

handle firmly with both hands during operation.

Install the loop handle so that its protrusion will fit into

the matching hole in the gear housing. (Fig. 1)

Install the bolts and tighten them with the hex wrench.

The loop handle can be installed in two different

directions as shown in Fig.2&3, whichever is con-

venient for your work. (Fig.2&3)

Shaft lock (Fig. 4)

Press the shaft lock to prevent spindle rotation when

installing or removing accessories such as wool pads.

CAUTION:

Never actuate the shaft lock when the spindle is

moving. The tool may be damaged.

Installing or removing wool pad (Fig.1&5)

Important:

Always be sure that the tool is switched off and

unplugged before installing or removing the wool pad.

To install the wool pad, first remove all dirt or foreign

matter from the backing pad. Press the shaft lock and

screw the backing pad onto the spindle. Insert the

sleeve 18 into the center hole of the backing pad.

Using the sleeve 18 as a positioning guide, install the

wool pad on the backing pad with the sleeve 18

inserted through the center hole of the wool pad. Then

remove the sleeve 18 from the backing pad. To

remove the wool pad, just tear it off the backing pad.

Then unscrew the backing pad while pressing the

shaft lock.

Switch action (Fig. 6)

CAUTION:

Before plugging in the tool, always check to see that

the switch trigger actuates properly and returns to the

‘‘OFF’’ position when released.

To start the tool, simply pull the trigger. Tool speed is

increased by increasing pressure on the trigger.

Release the trigger to stop. For continuous operation,

pull the trigger and then push in the lock button. To

stop the tool from the locked position, pull the trigger

fully, then release it.

Speed adjusting dial (Fig. 7)

The tool speed can be infinitely adjusted between

600 rpm and 3,000 rpm (rpm at the time when the

switch trigger is fully pulled) by turning the speed

adjusting dial to a given number setting from 1 to 6.

Higher speed is obtained when the dial is turned in the

direction of number 6; lower speed is obtained when

it is turned in the direction of number 1. Refer to the

table below for the relationship between the number

settings on the dial and the approximate tool speed.

Number RPM (min

–1

)

1–2 600–900

2 – 3 900 – 1,500

3 – 4 1,500 – 2,100

4 – 5 2,100 – 2,700

5 – 6 2,700 – 3,000

CAUTION:

•

If the tool is operated continuously at low speeds for

a long time, the motor will get overloaded and

heated up.

•

The speed adjusting dial can be turned only as far

as 6 and back to 1. Do not force it past 6 or 1, or the

speed adjusting function may no longer work.

Polishing operation (Fig. 8)

CAUTION:

Always wear safety glasses or a face shield during

operation.

Pull the trigger and turn the speed adjusting dial until

you obtain the appropriate speed for your work. When

polishing, keep the wool pad at an angle of about 15°

to the workpiece surface.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Makita 9227 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Makita 9227 Manual

Product: