391169
6
Zoom out
Zoom in
Previous page
1/14
Next page
6
23. Do not use the tool on any materials containing
asbestos.
24. Do not use water or grinding lubricant.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing wheel guard (Fig. 1)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the wheel guard.
When installing a depressed center wheel or an abrasive
cut-off wheel, always use a wheel guard. Mount the
wheel guard with the tab on the wheel guard band
aligned with the notch on the bearing box. Then rotate
the wheel guard 160 degrees counterclockwise. Be sure
to tighten the screw securely.
Installing side grip (auxiliary handle) (Fig. 2)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the side grip.
Always install the side grip on the tool securely before
operation. The side grip can be installed in any of three
positions on the sides of the tool, whichever is convenient
and keeps the guard properly positioned. Always hold the
tools switch handle and the side grip firmly with both
hands during operation.
Shaft lock (Fig. 3)
Press the shaft lock to prevent spindle rotation when
installing or removing accessories.
CAUTION:
Never actuate the shaft lock when the spindle is moving.
The tool may be damaged.
Installing or removing depressed center wheel
(Fig. 4 & 5)
Important:
Always be sure that the tool is switched off and
unplugged before installing or removing the wheel.
Mount the inner flange onto the spindle. Fit the wheel on
over the inner flange and screw the lock nut onto the
spindle.
To tighten the lock nut, press the shaft lock firmly so that
the spindle cannot revolve, then use the lock nut wrench
and securely tighten clockwise.
To remove the wheel, follow the installation procedure in
reverse.
NOTE:
Super flange
Models 9067F, 9069F, 9067SF and 9069SF are stan-
dard-equipped with a super flange.
Only 1/3 of efforts needed to undo lock nut, compared
with conventional type.
Switch action (Fig. 6)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the OFF
position when released.
For U.K., Australia, New Zealand, France, Réunion
and Algeria
To prevent the trigger from being accidentally actuated, a
lock lever is provided. To start the tool, push the lock lever
in and then pull the trigger. Release the trigger to stop.
For Germany, Austria, Italy, Netherlands, Belgium,
Spain, Portugal, Denmark, Sweden, Norway, Finland,
Greece and South Africa
To prevent the trigger from being accidentally actuated, a
lock lever is provided. To start the tool, push the lock lever
in and then pull the trigger. Release the trigger to stop.
For continuous operation, push the lock lever in, pull the
trigger and then push the lock lever further in. To stop the
tool from the locked position, pull the trigger fully, then
release it.
For other countries than the above countries
To start the tool, simply pull the trigger. Release the trig-
ger to stop. For continuous operation, pull the trigger and
then push the lock lever. To stop the tool from the locked
position, pull the trigger fully, then release it.
NOTE:
Models 9067S and 9069S begin to run slowly when they
are turned on. This soft start feature assures smoother
operation and less operator fatigue.
Operation (Fig. 7)
CAUTION:
After operation, always switch off the tool and wait until
the wheel has come to a complete stop before putting the
tool down.
Hold the tool firmly. Turn the tool on and then apply the
wheel or disc to the workpiece.
In general, keep the edge of the wheel or disc at an angle
of about 15° 30° to the workpiece surface. During the
break-in period with a new wheel, do not work the tool in
the B direction or it will cut into the workpiece. Once the
edge of the wheel has been rounded off by use, the
wheel may be worked in both A and B directions.
WARNING:
It should never be necessary to force the tool. The
weight of the tool applies adequate pressure. Forcing
and excessive pressure could cause dangerous wheel
breakage.
Continued use of a worn-out wheel may result in wheel
explosion and serious personal injury. Depressed cen-
ter wheel should not be used after it has been worn
down to 115 mm in diameter. Use of the wheel after
this point is unsafe and it should be removed from ser-
vice and rendered unusable by intentional destruction.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 9069 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 9069 in the language / languages: English, German, Dutch, Danish, French, Italian, Norwegian as an attachment in your email.

The manual is 0,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info