448256

Makita 906 Manual

4
Zoom out
Zoom in
Previous page
1/12
Next page
ENGLISH
Explanation of general view
1 Tighten
2 Loosen
3 Wrench 17
4 Wrench 10
5 Collet nut
6 Switch
7 Dressing stone
SPECIFICATIONS
Model 906
Collet size ............................................ 6 mm or 1/4’’
Max. wheel point diameter ............................ 19 mm
No load speed (min
-1
) .................................... 25,000
Overall length ............................................... 283 mm
Net weight ....................................................... 0.9 kg
•
Due to our continuing program of research and
development, the specifications herein are subject
to change without notice.
•
Note: Specifications may differ from country to
country.
Power supply
The tool should be connected only to a power supply
of the same voltage as indicated on the nameplate,
and can only be operated on single-phase AC supply.
They are double-insulated in accordance with Euro-
pean Standard and can, therefore, also be used from
sockets without earth wire.
Safety hints
For your own safety, please refer to the enclosed
safety instructions.
ADDITIONAL SAFETY RULES
FOR TOOL
ENB044-1
1. Always wear safety goggles and ear protec-
tors during operation.
2. Use only wheels with correct size and wheels
having a maximum operating speed at least as
high as the highest No Load Speed marked on
the tool’s nameplate.
3. Check the wheel carefully for cracks or dam-
age before operation. Replace cracked or
damaged wheel immediately.
4. Observe the instructions of the manufacturer
for correct mounting and use of wheels.
Handle and store wheels with care.
5. Before using the tool on an actual workpiece,
test run the tool at the highest no load speed
for at least 30 seconds in a safe position. Stop
immediately if there is any vibration or wob-
bling that could indicate poor installation or a
poorly balanced wheel. Check the tool to
determine the cause.
6. Check that the workpiece is properly sup-
ported.
7. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord.
Contact with a ‘‘live’’ wire will make exposed
metal parts of the tool ‘‘live’’ and shock the
operator.
8. Make sure the wheel is not contacting the
workpiece before the switch is turned on.
9. Watch out for flying sparks. Hold the tool so
that sparks fly away from you and other per-
sons or flammable materials.
10. Pay attention that the wheel continues to
rotate after the tool is switched off.
11. Hold the tool firmly.
12. Keep hands away from rotating parts.
13. Do not leave the tool running. Operate the tool
only when hand-held.
14. Do not touch the workpiece immediately after
operation; it may be extremely hot and could
burn your skin.
15. Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
16. Do not use the tool on any materials contain-
ing asbestos.
17. Do not use water or grinding lubricant.
18. Do not use this tool as cutter.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing wheel point (Fig.1&2)
Important:
•
Always be sure that the tool is switched off and
unplugged before installing or removing the wheel
point.
•
Ensure that the wheel point dimensions are com-
patible with the grinder and that the wheel point fits
the spindle.
Loosen the collet nut and insert the wheel point into
the collet nut. Use the smaller wrench to hold the
spindle and the larger one to tighten the collet nut
securely.
The wheel point should not be mounted more than
10 mm from the collet nut.
Exceeding this distance could cause vibration or a
broken shaft.
To remove the wheel point, follow the installation
procedure in reverse.
Switch action (Fig. 3)
To start the tool, move the switch to the ‘‘ON’’ position.
To stop, move the switch to the ‘‘OFF’’ position.
4
906 (Eng) (’100. 12. 13)
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 906 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 906 in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info