690983

Makita 6960D Manual

5
Zoom out
Zoom in
Previous page
1/56
Next page
Installing or removing bit
CAUTION:
Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the bit.
Use only the driver bit or socket bit shown in the figure below.
Do not use any other driver bit or socket bit.
To install the bit, pull the sleeve in the direction of the arrow and insert the bit into the sleeve as far as it will go. Then
release the sleeve to secure the bit. (Fig. 3)
To remove the bit, pull the sleeve in the direction of the arrow and pull the bit out firmly.
CAUTION:
•
This tool is designed to drive wood screws. Do not use this tool to drive machine screws or bolts. The tool may be
damaged.
•
If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will
not be secured. In this case, try re-inserting the bit according to the instructions above.
NOTE:
If the bit is not inserted deep enough into the sleeve, the sleeve will not return to its original position and the bit will not
be secured. In this case, try re-inserting the bit according to the instructions above.
Switch action (Fig. 4)
CAUTION:
Before inserting the battery cartridge into the tool, always
check to see that the switch trigger actuates properly and
returns to the ‘‘OFF’’ position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger. Release
the trigger to stop.
Reversing switch action (Fig. 5)
CAUTION:
•
Always check the direction of rotation before operation.
•
Use the reversing switch only after the tool comes to a
complete stop. Changing the direction of rotation before
the tool stops may damage the tool.
•
When not operating the tool, always set the reversing
switch lever to the neutral position.
This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for counter-
clockwise rotation. When the switch lever is in the neutral
position, the switch trigger cannot be pulled.
Installing set plate (Fig. 6)
Always install the set plate when using battery cartridges
1200, 1202 or 1202A. Install the set plate on the tool with
the screw provided as shown in Fig. 6.
Characteristics of Cordless Oil-Impulse Driver
The Makita Cordless Oil-Impulse Driver is a hydraulically
operated impact tool using oil viscosity to produce
impacts. Since oil viscosity changes with the temperature,
be aware of the following two points when operating the
tool.
1) If the tool itself is cold, it may take longer to set screws
because of the low fastening torque when you begin
operation. After fastening about ten screws, however,
the fastening torque will become normal.
2) The tool can overheat, causing a failure or hand burn
if you operate it continuously for long hours. Let the
tool cool off for more than 30 minutes before chang-
ing batteries during a long, continuous job.
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and the battery
cartridge is removed before carrying out any work on the
tool.
Replacement of carbon brushes (Fig.7&8)
Replace carbon brushes when they are worn down to the
limit mark. Both identical carbon brushes should be
replaced at the same time.
To maintain product safety and reliability, repairs, main-
tenance or adjustment should be carried out by Makita
Authorized Service Center.
5
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Makita 6960D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Makita 6960D in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 0,32 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info